參數資料
型號： L6712Q
廠商： STMICROELECTRONICS
元件分類： 穩壓器
英文描述： 2 A SWITCHING CONTROLLER, QCC36
封裝： 6 X 6 MM, 1 MM HEIGHT, VFQFPN-36
文件頁數： 6/29頁
文件大小： 624K
代理商： L6712Q
L6712A L6712
14/29
usual way until another OCP event is detected.
This means that the average current delivered can slightly increase also in Over Current condition since
the current ripple increases. In fact, the ON time increases due to the OFF time rise because of the current
has to reach the IOCPx bottom. The worst-case condition is when the ON time reaches its maximum value.
When this happens, the device works in Constant Current and the output voltage decrease as the load
increase. Crossing the UVP threshold causes the device to reset.
Figure 10 shows this working condition.
It can be observed that the peak current (Ipeak) is greater than the IOCPx but it can be determined as follow:
Where VoutMIN is the minimum output voltage (VID-40% as follow).
The device works in Constant-Current, and the output voltage decreases as the load increase, until the
output voltage reaches the under-voltage threshold (VoutMIN).
The maximum average current during the Constant-Current behavior results:
In this particular situation, the switching frequency results reduced. The ON time is the maximum allowed
(TonMAX) while the OFF time depends on the application:
Figure 10. Constant Current operation
Over current is set anyway when IINFOx reaches 35A (IFB=70A). The full load value is only a convention
to work with convenient values for IFB. Since the OCP intervention threshold is fixed, to modify the per-
centage with respect to the load value, it can be simply considered that, for example, to have on OCP
threshold of 200%, this will correspond to IINFOx = 35A (IFB = 70A). The full load current will then corre-
spond to IINFOx = 17.5A (IFB = 35A).
Once the UVP threshold has been intercepted, the device resets with all power mosfets turned OFF. An-
other soft start is then performed allowing the device to recover from OCP once the over load cause has
been removed.
Crossing the UVP threshold causes the device to reset: all mosfets are turned off and a new soft start is
I
peak
I
OCPx
V
IN
Vout
min
–
L
-------------------------------------- Ton
MAX
I
OCPx
V
IN
Vout
MIN
–
L
--------------------------------------- 0.40 T
+
=
+
=
I
MAX,TOT
2I
MAX
2I
OCPx
Ipeak
I
OCPx
–
2
--------------------------------------
+
=
=
T
OFF
L
Ipeak
I
OCPx
–
V
OUt
--------------------------------------
f
1
T
ONmax
T
OFF
+
------------------------------------------
=
=
a) Maximum current for each phase
b) Output Characteristic
TonMAX
IOCPx
Ipeak
IMAX
Vout
Iout
(IDROOP=50A)
2IOCPx (IDROOP=70A)
IMAX,TOT
UVP
Droop effect
相關PDF資料
PDF描述
L6712ADTR 2 A SWITCHING CONTROLLER, PDSO28
L6712D 2 A SWITCHING CONTROLLER, PDSO28
L6712QTR 2 A SWITCHING CONTROLLER, QCC36
L6725ATR 20 A SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO16
L6727TR 1.5 A SWITCHING CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
L6712QTR 功能描述:開關變換器、穩壓器與控制器 2-Ph Interleaved RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
L6712大電流DCDC轉換器 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
L6713A 功能描述:DC/DC 開關控制器 2/3 Phase controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
L6713A_0805 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:2/3/4 phase controller with embedded drivers for Intel VR11.1
L6713ATR 功能描述:DC/DC 開關控制器 2/3 Phase controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*