- 您現在的位置：買賣IC網 > PDF目錄367494 > L9216A CAP CER 270PF 3.15KVDC R3 RAD PDF資料下載
參數資料
| 型號： | L9216A |
| 英文描述： | CAP CER 270PF 3.15KVDC R3 RAD |
| 中文描述： | 短環振鈴用戶接口與地面開始 |
| 文件頁數： | 24/48頁 |
| 文件大小： | 1062K |
| 代理商： | L9216A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Preliminary Data Sheet
September 2001
Short-Loop Ringing SLIC with Ground Start
L9216A/G
24
Agere Systems Inc.
Applications
(continued)
Overhead Voltage
(continued)
Ring Mode
In the ring mode, to maximize ringing loop length, the
overhead is decreased to the saturation of the tip ring
drive amplifiers, a nominal 4 V. The tip to ground volt-
age is 1 V, and the ring to V
BAT1
voltage is 3 V.
During the ring mode, to conserve power, the receive
input at RCVN/RCVP is deactivated. During the ring
mode, to conserve power, the AAC amplifier in the
transmit direction at VITR is deactivated. However, if
the AX amplifier at VTX is active during the ring mode,
differential ring current may be sensed at VTX during
the ring mode.
Loop Range
The dc loop range is calculated using:
R
L
=
– 2R
P
– R
DC
V
BAT2
is typically applied under off-hook conditions for
power conservation and SLIC thermal considerations.
The L9216 is intended for short-loop applications and,
therefore, will always be in current limit during off-hook
conditions. However, note that the ringing loop length
rather than the dc loop length, will be the factor to
determine operating loop length.
Battery Reversal Rate
The rate of battery reverse is controlled or ramped by
capacitors FB1 and FB2. Table 20 below shows FB1
and FB2 values vs. typical ramp time. Leave FB1 and
FB2 open if it is not desired to ramp the rate of battery
reversal.
Table 20. FB1 and FB2 Values vs. Typical Ramp
Time
Supervision
The L9216 offers the loop closure and ring trip supervi-
sion functions. Internal to the device, the outputs of
these detectors are multiplexed into a single package
output, NSTAT. Additionally, a common-mode current
detector for tip or ring ground detection is included for
ground key applications.
Loop Closure
The loop closure has a fixed typical 10.5 mA on- to off-
hook threshold in the active mode and a fixed 11.5 mA
on- to off-hook threshold from the scan mode. In either
case, there is a 2 mA hysteresis with V
CC
= 5 V and a
1 mA hysteresis with V
CC
= 3.3 V.
Ring Trip
The ring trip detector requires only a single-pole filter at
the input, minimizing external components. An R/C
combination of 383 k
and 0.1
μ
F, for a filter pole at
5.15 Hz, is recommended.
The ring trip threshold is internally fixed as a function of
battery voltage and is given by:
RT (mA) = 67 * {(0.0045 * V
BAT1
) + 0.317}
where:
RT is ring trip current in mA.
V
BAT1
is the magnitude of the ring battery in V.
There is a 6 mA to 8 mA hysteresis.
Tip or Ring Ground Detector
In the ground key or ground start applications, a com-
mon-mode current detector is used to indicate either a
tip- or ring-ground has occurred (ground key) or an off-
hook has occurred (ground start).
For ground start applications detection may be seen at
the output of the common mode current detector
(RGDET) or the loop closure detector (NSTAT).
If ICM is used, the detection threshold is set by con-
necting a resistor from ICM to V
CC
.
205 x V
CC
/R
ICM
(k
) = I
TH
(mA)
Additionally, a filter capacitor across R
ICM
will set the
time constant of the detector. No hysteresis is associ-
ated with this detector. The RC filter at ICM gives
immunity to longitudinal currents.
C
FB1
and C
FB2
0.01
μ
F
0.1
μ
F
0.22
μ
F
0.47
μ
F
1.0
μ
F
1.22
μ
F
1.3
μ
F
1.4
μ
F
1.6
μ
F
Transition Time
20 ms
220 ms
440 ms
900 ms
1.8 s
2.25 s
2.5 s
2.7 s
3.2 s
--------------------------------------
I
LIMIT
相關PDF資料 |
PDF描述 |
|---|---|
| L9217A | CAP CER 2700PF 3.15KVDC R3 RAD |
| L9218A | CAP CER 330PF 3.15KVDC R3 RAD |
| L9219A | CAP CER 390PF 3.15KVDC R3 RAD |
| L9310 | Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device |
| L9311 | Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L9217A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM |
| L9218A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface |
| L9219A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit |
| L9222 | 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L9222_04 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD INVERTING TRANSISTOR SWITCH |
發布緊急采購，3分鐘左右您將得到回復。