參數資料
型號： L9216A
英文描述： CAP CER 270PF 3.15KVDC R3 RAD
中文描述： 短環振鈴用戶接口與地面開始
文件頁數： 30/48頁
文件大?。?/td> 1062K
代理商： L9216A
Preliminary Data Sheet
September 2001
Short-Loop Ringing SLIC with Ground Start
L9216A/G
30
Agere Systems Inc.
Supervision
(continued)
Power Ring
(continued)
3.3 V V
CC
Operation
A PWM signal was generated with an HP8116 Func-
tion Generator modulated with a 20 Hz signal. The opti-
mal frequency used was 10 kHz. The PWM signal
amplitude was 3.10 V (0 V to 3.10 V). This input signal
is shown in Figure 17.
12-3571F
Figure 17. 3.3 V PWM Signal Amplitude
This produced 44.96 Vrms ringing signal on tip/ring
under open-loop conditions and 42.0 Vrms was deliv-
ered to 5 REN load. The ringing output on ring with V
CC
= 3.1 V is shown in Figure 18.
1660
Notes:
The modulating 20 Hz signal THD was measured at 1.3%.
The tip/ring 20 Hz signal THD was measured at 1%.
V
BAT1
= –70.6 V, V
BAT2
= –26.5 V, V
CC
= 3.10 V.
PWM input 10 kHz, 3.1 Vp-p.
R
1
= 10 k
, C
1
= 0.22
μ
F, C
2
= 0.47
μ
F.
Figure 18. Ringing Output on RING, with V
CC
= 3.1 V
During nonring modes, the PWM waveform may be left
on at RING
IN
. Via the state table, the ring signal will be
removed from tip and ring even if the low-voltage input
is still present at RING
IN
. There are certain timing con-
siderations that should be made with respect to state
changes which are detailed in the Switching Behavior
of L9215/6 Ringing SLICApplication Note.
Square Wave Input Signal and Trapezoidal Power
Ring Signal Output
A low-voltage square wave signal may be used to pro-
vide the ringing input to RING
IN
. The signal is applied
through a low-pass filter and ac-coupled into RING
IN
as
shown in Figure 13 and Table 23. This approach gives
a trapezoidal wave output at tip and ring.
Using this approach, a trapezoidal waveform can be
achieved at tip and ring. This has the advantage of
increasing the power transfer to the load for a given
battery voltage, thus increasing the effective ringing
loop length as compared to a sine wave. The actual
crest factor achieved is a function of the magnitude of
the battery, the magnitude of the input voltage, fre-
quency, and R
1
.
12-3572F
Notes:
CH1—CMOS Input (5 V) at RING
IN
.
CH2—Filtered input at RING
IN
.
CH3—Tip.
CH4—Ring.
R
1
= 14 k
, C
1
= 1.0
μ
F, C
2
= 0.47
μ
F.
V
BAT1
= –70 V, Vrms
= 51 V, V
p-p
= 67 V, frequency = 20 Hz, Crest
Factor = 1.3.
Figure 19. Square Wave Input Signal and Trapezoi-
dal Power Ring Signal Output
CH1
CH2
CH3
CH4
相關PDF資料
PDF描述
L9217A CAP CER 2700PF 3.15KVDC R3 RAD
L9218A CAP CER 330PF 3.15KVDC R3 RAD
L9219A CAP CER 390PF 3.15KVDC R3 RAD
L9310 Line Interface and Line Access Circuit Full-Feature SLIC,Ringing Relay,and Test Access Device
L9311 Line Interface and Line Access Circuit Full-Feature SLIC with High Longitudinal Balance, Ringing Relay,and GR-909 Test Access
相關代理商/技術參數
參數描述
L9217A 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and PPM
L9218A 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface
L9219A 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Line Interface with Reverse Battery and Dual Current Limit
L9222 功能描述:功率驅動器IC Quad Inv Tran Switch RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
L9222_04 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD INVERTING TRANSISTOR SWITCH
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*