參數資料
型號： L9942
廠商： STMICROELECTRONICS
元件分類： 運動控制電子
英文描述： STEPPER MOTOR CONTROLLER, PDSO36
封裝： POWER, SO-36
文件頁數： 18/21頁
文件大?。?/td> 161K
代理商： L9942
ing edge causes an interrupt request on the interrupt line #0. If the overvoltage situation is still present,
OV is SET again. The bridge is switched off automatically at overvoltage.
UNV: This bit is SET as soon as the voltage on VS pin falls below the undervoltage threshold Vsmin.
This rising edge causes a interrupt request on the interrupt line #0. This bit is RESET by software only. If
the undervoltage situation is still present, UNV remains SET. The bridge is not switched off automatically
at undervoltage.
OVT1: This bit is SET as soon as the temperature of the chip exceeds 130
°C. This rising edge causes
an interrupt request on the interrupt line #0. This bit is RESET by software only. If the overtemperature
situation is still present, OVT1 remains SET. The bridge is not switched off automatically at overtem-
perature.
OVT2: This bit is SET as soon as the temperature of the chip exceeds 150
°C. This rising edge causes
an interrupt request on the interrupt line #0. This bit is RESET by software only. If the overtemperature
situation is still present, OVT2 remains SET. The bridge is not switched off automatically at overtem-
perature.
Warning: All power bridge flags are ored to form one interrupt request which is connected to edge sen-
sitive interrupt input #0 (see Fig. 11). The interrupt request is stored in a flipflop which is automatically
cleared when the interrupt service routine is entered. If other interrupt flags of the power bridge become
active before the flag which caused the interrupt is cleared by software, the new request is not stored in
the flipflop. In order not to miss any interrupt request it is recommended to check all interrupt flags of the
power bridge after clearing the first flag. Then the interrupt service routine may be left.
Voltage regulator
The on chip voltage regulator provides regulated 5V to supply the microcontroller and it’s periphery. This
voltage is available at pin VCC to supply external components and connect a capacitor to optimize EMI
performance. The regulator has a normal and a standby operating mode. When the controller enters
STOP mode, the regulator is switched to stand by operation. In this mode the power consumption as
well as the ability to supply current (also to external devices) is drastically reduced. A return to RUN
mode or a reset switches the regulator back to normal mode.
The voltage regulator also provides a reset signal POR at power up and power down to guarantee a well
defined state of the device at undervoltage conditions (see Fig. 1).
POR activates the reset pull down transistor performing a complete chip reset. In the same way a reset
POWER SUPPLY (continued)
undefined
VCC
POR
5V
V Reset OFF
Reset ON
V
t
Reset UD
V
Figure 1. Power up/down characteristics
L9942
6/21
相關PDF資料
PDF描述
LA5681FN SWITCHING CONTROLLER, 520 kHz SWITCHING FREQ-MAX, QCC48
LB11620T BRUSHLESS DC MOTOR CONTROLLER, 0.25 A, PDSO24
LB11875 BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO36
LB11923V BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO44
LB11923V BRUSHLESS DC MOTOR CONTROLLER, 0.03 A, PDSO44
相關代理商/技術參數
參數描述
L9942XP1 功能描述:低壓差穩壓器 - LDO Integrated Stepper Bipolar Motor Driver RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20
L9942XP1TR 功能描述:馬達/運動/點火控制器和驅動器 Integrated Stepper Bipolar Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
L9946 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC Motor Controller/Driver
L9947 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:QUAD HALF-BRIDGE AND SINGLE HIGH-SIDE DRIVER
L9947L 制造商:STMicroelectronics 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*