參數資料
型號: LAN91C100
廠商: SMSC Corporation
英文描述: FEAST⑩ Fast Ethernet Controller
中文描述: 宴⑩快速以太網控制器
文件頁數: 44/101頁
文件大?。?/td> 312K
代理商: LAN91C100
44
The possible sources are:
LINK - Link Test transition
CTR_ROL - Statistics counter roll over
TXENA cleared - A fatal transmit error
occurred forcing TXENA to be cleared.
TX_SUC will be low and the specific reason
will be reflected by the bits:
TXUNRN - Transmit underrun
SQET - SQE Error
LOST CARR - Lost Carrier
LATCOL - Late Collision
16COL - 16 collisions
RX_OVRN INT Set when the receiver overruns
due to a failed memory allocation. The
RX_OVRN bit of the EPHSR will also be set, but
if a new packet is received it will be cleared. The
RX_OVRN INT bit, however, latches the overrun
condition for the purpose of being polled or
generating an interrupt, and will only be cleared
by writing the acknowledge register with the
RX_OVRN INT bit set.
ALLOC INT Set when an MMU request for TX
pages allocation is completed. This bit is the
complement
of
the
ALLOCATION RESULT register. The ALLOC
INT ENABLE bit should only be set following an
allocation command, and cleared upon servicing
the interrupt.
FAILED
bit
in
the
TX EMPTY INT Set if the TX FIFO goes empty,
can be used to generate a single interrupt at the
end of a sequence of packets enqueued for
transmission. This bit latches the empty
condition, and the bit will stay set until it is
specifically cleared by writing the acknowledge
register with the TX EMPTY INT bit set. If a
real time reading of the FIFO empty is desired,
the bit should be first cleared and then read.
The TX EMPTY INT ENABLE should only be set
after the following steps:
a)
b)
a packet is enqueued for transmission
the previous empty condition is cleared
(acknowledged)
TX INT Set when at least one packet
transmission was completed. The first packet
number to be serviced can be read from the
FIFO PORTS register. The TX INT bit is always
the logic complement of the TEMPTY bit in the
FIFO PORTS register. After servicing a packet
number, its TX INT interrupt is removed by
writing the Interrupt Acknowledge Register with
the TX INT bit set.
RCV INT Set when a receive interrupt is
generated. The first packet number to be
serviced can be read from the FIFO PORTS
register. The RCV INT bit is always the logic
complement of the REMPTY bit in the FIFO
PORTS register.
Note: If the driver uses AUTO RELEASE mode
it should enable TX EMPTY INT as well as TX
INT. TX EMPTY INT will be set when the
complete sequence of packets is transmitted.
TX INT will be set if the sequence stops due to a
fatal error on any of the packets in the
sequence.
Note: For edge triggered systems, the Interrupt
Service Routine should clear the Interrupt Mask
Register, and only enable the appropriate
interrupts after the interrupt source is serviced
(acknowledged).
相關PDF資料
PDF描述
LAN91C110 FEAST FAST ETHERNET CONTROLLER FOR PCMCIA AND GENERIC 16-BIT APPLICATIONS
LAN91C96(100TQFP) LAN Node Controller
LAN91C96(100QFP) LAN Node Controller
LAN91C95 LAN Node Controller
LAN91C100FD(208TQFP) LAN Node Controller
相關代理商/技術參數
參數描述
LAN91C100FD 制造商:- 功能描述: 制造商:SMSC 功能描述:
LAN91C100-FD 制造商:SMSC 制造商全稱:SMSC 功能描述:FEAST Fast Ethernet Controller with Full Duplex Capability
LAN91C100FD(208PQFP) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller
LAN91C100FD(208TQFP) 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller
LAN91C100FD_06 制造商:SMSC 制造商全稱:SMSC 功能描述:FEAST Fast Ethernet Controller with Full Duplex Capability