- 您現在的位置：買賣IC網 > PDF目錄69004 > LIS3LV02DL (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA16 PDF資料下載
參數資料
| 型號： | LIS3LV02DL |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| 封裝： | 4.40 X 7.50 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件頁數： | 16/48頁 |
| 文件大小： | 681K |
| 代理商： | LIS3LV02DL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
LIS3LV02DL
Digital interfaces
23/48
5.1.1
I2C operation
The transaction on the bus is started through a START (ST) signal. A START condition is
defined as a HIGH to LOW transition on the data line while the SCL line is held HIGH. After
this has been transmitted by the Master, the bus is considered busy. The next byte of data
transmitted after the start condition contains the address of the slave in the first 7 bits and
the eighth bit tells whether the Master is receiving data from the slave or transmitting data to
the slave. When an address is sent, each device in the system compares the first seven bits
after a start condition with its address. If they match, the device considers itself addressed
by the Master. The Slave ADdress (SAD) associated to the LIS3LV02DL is 0011101b.
Data transfer with acknowledge is mandatory. The transmitter must release the SDA line
during the acknowledge pulse. The receiver must then pull the data line LOW so that it
remains stable low during the HIGH period of the acknowledge clock pulse. A receiver which
has been addressed is obliged to generate an acknowledge after each byte of data
received.
The I2C embedded inside the LIS3LV02DL behaves like a slave device and the following
protocol must be adhered to. After the start condition (ST) a salve address is sent, once a
slave acknowledge (SAK) has been returned, a 8-bit sub-address will be transmitted: the 7
LSb represent the actual register address while the MSB enables address auto increment. If
the MSb of the SUB field is 1, the SUB (register address) will be automatically incremented
to allow multiple data read/write.
The slave address is completed with a Read/Write bit. If the bit was ‘1’ (Read), a repeated
START (SR) condition will have to be issued after the two sub-address bytes; if the bit is ‘0’
(Write) the Master will transmit to the slave with direction unchanged.
Table 11.
Transfer when master is writing one byte to slave
Master
ST
SAD + W
SUB
DATA
SP
Slave
SAK
Table 12.
Transfer when master is writing multiple bytes to slave
Master
ST
SAD + W
SUB
DATA
SP
Slave
SAK
Table 13.
Transfer when master is receiving (reading) one byte of data from slave
Master
ST
SAD + W
SUB
SR
SAD + R
NMAK
SP
Slave
SAK
DATA
Table 14.
Transfer when master is receiving (reading) multiple bytes of data from slave
Master
ST SAD+W
SUB
SR SAD+R
MAK
NMAK
SP
Slave
SAK
DATA
相關PDF資料 |
PDF描述 |
|---|---|
| LM10010SD | SWITCHING REGULATOR, PDSO10 |
| LM10010SDX | SWITCHING REGULATOR, PDSO10 |
| LM12L458CIVX | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LM185BYH-MLS | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, MBCY3 |
| LM234H/NOPB | SPECIALTY ANALOG CIRCUIT, MBCY3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS3LV02DL_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS inertial sensor 3-axis - 【2g/【6g digital output low voltage linear accelerometer |
| LIS3LV02DLTR | 功能描述:加速計 - 板上安裝 MEMS INERTIAL snsr 3 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3LV02DL-TR | 制造商:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR |
| LIS3LV02DQ | 功能描述:加速計 - 板上安裝 3-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3LV02DQ-TR | 功能描述:加速計 - 板上安裝 INERTIAL SENSOR Lo Vltg 3Axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
發布緊急采購，3分鐘左右您將得到回復。