- 您現在的位置：買賣IC網 > PDF目錄69004 > LIS3LV02DL (STMICROELECTRONICS) SPECIALTY ANALOG CIRCUIT, PBGA16 PDF資料下載
參數資料
| 型號： | LIS3LV02DL |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PBGA16 |
| 封裝： | 4.40 X 7.50 MM, 1 MM HEIGHT, GREEN, PLASTIC, LGA-16 |
| 文件頁數： | 26/48頁 |
| 文件大小： | 681K |
| 代理商： | LIS3LV02DL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
Register description
LIS3LV02DL
32/48
PD1, PD0 bit allows to turn the device out of power-down mode. The device is in power-
down mode when PD1, PD0= “00” (default value after boot). The device is in normal mode
when either PD1 or PD0 is set to 1.
DF1, DF0 bit allows to select the data rate at which acceleration samples are produced. The
default value is “00” which corresponds to a data-rate of 40 Hz. By changing the content of
DF1, DF0 to “01”, “10” and “11” the selected data-rate will be set respectively equal to
160 Hz, 640 Hz and to 2560 Hz.
ST bit is used to activate the self test function. When the bit is set to one, an output change
will occur to the device outputs (refer to table 2 and 3 for specification) thus allowing to
check the functionality of the whole measurement chain.
Zen bit enables the Z-axis measurement channel when set to 1. The default value is 1.
Yen bit enables the Y-axis measurement channel when set to 1. The default value is 1.
Xen bit enables the X-axis measurement channel when set to 1. The default value is 1.
7.9
CTRL_REG2 (21h)
ST
Self Test Enable
(0: normal mode; 1: self-test active)
Zen
Z-axis enable
(0: axis off; 1: axis on)
Yen
Y-axis enable
(0: axis off; 1: axis on)
Xen
X-axis enable
(0: axis off; 1: axis on)
Table 31.
Register description (continued) (20h)
Table 32.
Register (21h)
FS
BDU
BLE
BOOT
IEN
DRDY
SIM
DAS
Table 33.
Register description (21h)
FS
Full Scale selection
(0: ±2g; 1: ±6g)
BDU
Block Data Update
(0: continuous update; 1: output registers not updated between MSB and LSB
reading)
BLE
Big/Little Endian selection
(0: little endian; 1: big endian)
BOOT
Reboot memory content
IEN
Interrupt ENable
(0: data ready on RDY pad; 1: interrupt events on RDY pad)
DRDY
Enable Data-Ready generation
相關PDF資料 |
PDF描述 |
|---|---|
| LM10010SD | SWITCHING REGULATOR, PDSO10 |
| LM10010SDX | SWITCHING REGULATOR, PDSO10 |
| LM12L458CIVX | SPECIALTY ANALOG CIRCUIT, PQCC44 |
| LM185BYH-MLS | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.24 V, MBCY3 |
| LM234H/NOPB | SPECIALTY ANALOG CIRCUIT, MBCY3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LIS3LV02DL_08 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:MEMS inertial sensor 3-axis - 【2g/【6g digital output low voltage linear accelerometer |
| LIS3LV02DLTR | 功能描述:加速計 - 板上安裝 MEMS INERTIAL snsr 3 axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3LV02DL-TR | 制造商:STMicroelectronics 功能描述:MEMS INERTIAL SENSOR |
| LIS3LV02DQ | 功能描述:加速計 - 板上安裝 3-axis +/-2g/+/-6g MEMS Intertial Sensr RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
| LIS3LV02DQ-TR | 功能描述:加速計 - 板上安裝 INERTIAL SENSOR Lo Vltg 3Axis RoHS:否 制造商:Murata 傳感軸:Double 加速:12 g 靈敏度: 封裝 / 箱體: 輸出類型:Analog 數字輸出 - 位數:11 bit 電源電壓-最大:5.25 V 電源電壓-最小:4.75 V 電源電流:4 mA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C |
發布緊急采購，3分鐘左右您將得到回復。