- 您現在的位置：買賣IC網 > PDF目錄358821 > LM2575 (ON SEMICONDUCTOR) 1.0 A, Adjustable Output Voltage, Step-Down Switching Regulator(1.0A,可調輸出電壓,降壓型開關穩壓器) PDF資料下載
參數資料
| 型號： | LM2575 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | 1.0 A, Adjustable Output Voltage, Step-Down Switching Regulator(1.0A,可調輸出電壓,降壓型開關穩壓器) |
| 中文描述： | 1.0甲，可調輸出電壓，降壓型開關穩壓器（1.0安培，可調輸出電壓，降壓型開關穩壓器） |
| 文件頁數： | 10/28頁 |
| 文件大小： | 363K |
| 代理商： | LM2575 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LM2575
http://onsemi.com
10
Procedure
(Fixed Output Voltage Version) (continued)
In order to simplify the switching regulator design, a stepbystep design
procedure and example is provided.
Procedure
Example
5. Output Capacitor Selection (C
out
)
A.
Since the LM2575 is a forwardmode switching regulator
with voltage mode control, its open loop 2pole2zero
frequency characteristic has the dominant polepair
determined by the output capacitor and inductor values. For
stable operation and an acceptable ripple voltage,
(approximately 1% of the output voltage) a value between
100 F and 470 F is recommended.
B.
Due to the fact that the higher voltage electrolytic capacitors
generally have lower ESR (Equivalent Series Resistance)
numbers, the output capacitor’s voltage rating should be at
least 1.5 times greater than the output voltage. For a 5.0 V
regulator, a rating at least 8V is appropriate, and a 10 V or
16 V rating is recommended.
5. Output Capacitor Selection (C
out
)
A.
C
out
= 100 F to 470 F standard aluminium electrolytic.
B.
Capacitor voltage rating = 16 V.
Procedure (Adjustable Output Version:
LM2575Adj)
Procedure
Example
Given Parameters:
V
out
= Regulated Output Voltage
V
in(max)
= Maximum DC Input Voltage
I
Load(max)
= Maximum Load Current
Given Parameters:
V
out
= 8.0 V
V
in(max)
= 12 V
I
Load(max)
= 1.0 A
1. Programming Output Voltage
To select the right programming resistor R1 and R2 value (see
Figure 14) use the following formula:
Resistor R1 can be between 1.0 k and 5.0 k . (For best
temperature coefficient and stability with time, use 1% metal
film resistors).
Vout
Vref
Vout
Vref
1
R2
R1
R2
R1
– 1
where V
ref
= 1.23 V
1. Programming Output Voltage
(selecting R1 and R2)
Select R1 and R2:
R2 = 9.91 k , choose a 9.88 k metal film resistor.
R2
R1
Vout
Vref
1
1.8 k
8.0 V
1.23 V
1
Vout
1.23 1
R2
2. Input Capacitor Selection (C
in
)
To prevent large voltage transients from appearing at the input
and for stable operation of the converter, an aluminium or
tantalum electrolytic bypass capacitor is needed between the
input pin +V
in
and ground pin GND This capacitor should be
located close to the IC using short leads. This capacitor should
have a low ESR (Equivalent Series Resistance) value
.
For additional information see input capacitor section in the
“External Components” section of this data sheet.
2. Input Capacitor Selection (C
in
)
A 100 F aluminium electrolytic capacitor located near the
input and ground pin provides sufficient bypassing.
3. Catch Diode Selection (D1)
A.
Since the diode maximum peak current exceeds the
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the maximum
load current. For a robust design, the diode should have a
current rating equal to the maximum current limit of the
LM2575 to be able to withstand a continuous output short.
B.
The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
3. Catch Diode Selection (D1)
A.
For this example, a 3.0 A current rating is adequate.
B.
Use a 20 V 1N5820 or MBR320 Schottky diode or any
suggested fast recovery diode in the
Table 4.
相關PDF資料 |
PDF描述 |
|---|---|
| LM2576D2T-12 | EASY SWITCHER 3.0 A STEP.DOWN VOLTAGE REGULATOR |
| LM2576D2T-12 | EASY SWITCHERE⑩ 3.0 A STEP-DOWN VOLTAGE REGULATOR |
| LM2576R | 3.0A, 15V, Step-Down Switching Regulator |
| LM2577S-12 | Pressure Transducer, Series 19 mm, Uncompensated, Pressure Range: 0 psi to 100 psi, Absolute, flush mount, 10 Vdc excitation |
| LM2577N-ADJ | Pressure Transducer, Series 19 mm, Compensated, Pressure Range: 0 psi to 200 psi, Absolute, flush mount with flange, 10 Vdc excitation |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM2575/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Easy Switcher? 1.0 A Step-Down Voltage Regulator |
| LM2575_05 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1.0 A, Adjustable Output Voltage, Step−Down Switching Regulator |
| LM2575_06 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1-A SIMPLE STEP-DOWN SWITCHING VOLTAGE REGULATOR |
| LM2575_09 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:52kHz Simple 1A Buck Regulator |
| LM2575-05IKC | 制造商:TI 制造商全稱:Texas Instruments 功能描述:1-A SIMPLE STEP DOWN SWITCHING VOLTAGE REGULATOR |
發布緊急采購，3分鐘左右您將得到回復。