- 您現在的位置：買賣IC網 > PDF目錄358849 > LM3671MF-1.875 (NATIONAL SEMICONDUCTOR CORP) 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 PDF資料下載
參數資料
| 型號： | LM3671MF-1.875 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| 中文描述： | 1.15 A SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PDSO5 |
| 封裝： | 2.92 X 2.84 MM, 1.20 MM HEIGHT, SOT-23, 5 PIN |
| 文件頁數： | 12/16頁 |
| 文件大?。?/td> | 967K |
| 代理商： | LM3671MF-1.875 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁
Operation Description
(Continued)
tions when the supply is less than 2.8V. Do not leave the EN
pin floating. Do not tie EN pin to V
IN
when powering up
LM3671-ADJ (V
OUT
≥
2.5V) with a slow input supply ramp.
SOFT START
The LM3671 has a soft-start circuit that limits in-rush current
during start-up. During start-up the switch current limit is
increased in steps. Soft start is activated only if EN goes
from logic low to logic high after Vin reaches 2.8V. Soft start
is implemented by increasing switch current limit in steps of
70mA, 140mA, 280mA and 1020mA (typ. switch current
limit). The start-up time thereby depends on the output ca-
pacitor and load current demanded at start-up. Typical
start-up times with 22μF output capacitor and 300mA load
current is 400 μs and with 1mA load current its 275μs.
LDO - LOW DROP OUT OPERATION
The LM3671-ADJ can operate at 100% duty cycle (no
switching, PMOS switch completely on) for low drop out
support of the output voltage. In this way the output voltage
will be controlled down to the lowest possible input voltage.
The minimum input voltage needed to support the output
voltage is
V
IN, MIN
= I
LOAD
*
(R
DSON, PFET
+ R
INDUCTOR
) + V
OUT
I
LOAD
R
DSON, PFET
Load current
Drain to source resistance of
PFET switch in the triode region
Inductor resistance
R
INDUCTOR
Application Information
OUTPUT VOLTAGE SELECTION FOR LM3671-ADJ
The output voltage of the adjustable parts can be pro-
grammed through the resistor network connected from V
OUT
to FB then to GND. V
OUT
will be adjusted to make the
voltage at FB equal to 0.5V. The resistor from FB to GND
(R2) should be 200 k
to keep the current drawn through
this network well below the 16 μA quiescent current level
(PFM mode) but large enough that it is not susceptible to
noise. If R2 is 200 k
, and given the V
is 0.5V, the current
through the resistor feedback network will be 2.5 μA.
The formula for output voltage selection is:
V
OUT
: output voltage (volts)
V
FB
: feedback voltage = 0.5V
R1: feedback resistor from V
OUT
to FB
For any output voltage greater than or equal to 0.8V a zero
must be added around 45 kHz for stability. The formula for
calculation of C1 is:
R2: feedback resistor from FB to GND
For output voltages between 0.7 and 0.8V and output volt-
ages higher than 2.5V a pole must be placed at 45 kHz as
well. The lowest output voltage possible is 0.7V. At low
output voltages the duty cycle is very small; in addition as the
input voltage increases the duty cycle decreases even fur-
ther. Since the duty cycle is so low it is very susceptible to
noise. C1 and C2 act as noise filters at this point rather than
frequency poles and zeroes. If the pole and zero are at the
same frequency the formula for calculation of C2 is:
The formula for location of zero and pole frequency created
by adding C1,C2 are given below. It can be seen that by
adding C1, a zero as well as a higher frequency pole is
introduced.
See the "LM3671-ADJ configurations for various V
"
table.These values are subject to change when the LM3671-
ADJ part is released.
L
www.national.com
12
相關PDF資料 |
PDF描述 |
|---|---|
| LM3671MF-ADJ | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| LM3671MFX-1.2 | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| LM3671MFX-1.25 | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| LM3671MFX-1.375 | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| LM3671MFX-1.5 | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3671MF-2.5 | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM3671MF-2.5/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM3671MF-2.8 | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM3671MF-2.8/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM3671MF-3.3 | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。