- 您現在的位置：買賣IC網 > PDF目錄358849 > LM3671MF-1.875 (NATIONAL SEMICONDUCTOR CORP) 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 PDF資料下載
參數資料
| 型號： | LM3671MF-1.875 |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| 中文描述： | 1.15 A SWITCHING REGULATOR, 2600 kHz SWITCHING FREQ-MAX, PDSO5 |
| 封裝： | 2.92 X 2.84 MM, 1.20 MM HEIGHT, SOT-23, 5 PIN |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 967K |
| 代理商： | LM3671MF-1.875 |
Application Information
(Continued)
Good layout for the LM3671 can be implemented by follow-
ing a few simple design rules, as illustrated in
Figure 8
.
1.
Place the LM3671, inductor and filter capacitors close
together and make the traces short.
The traces between
these components carry relatively high switching cur-
rents and act as antennas. Following this rule reduces
radiated noise. Special care must be given to place the
input filter capacitor very close to the V
IN
and GND pin.
2.
Arrange the components so that the switching current
loops curl in the same direction.
During the first half of
each cycle, current flows from the input filter capacitor
through the LM3671 and inductor to the output filter
capacitor and back through ground, forming a current
loop. In the second half of each cycle, current is pulled
up from ground through the LM3671 by the inductor to
the output filter capacitor and then back through ground
forming a second current loop. Routing these loops so
the current curls in the same direction prevents mag-
netic field reversal between the two half-cycles and re-
duces radiated noise.
3.
Connect the ground pins of the LM3671 and filter ca-
pacitors together using generous component-side cop-
per fill as a pseudo-ground plane. Then, connect this to
the ground-plane (if one is used) with several vias.
This
reduces ground-plane noise by preventing the switching
currents from circulating through the ground plane. It
also reduces ground bounce at the LM3671 by giving it
a low-impedance ground connection.
4.
Use wide traces between the power components and for
power connections to the DC-DC converter circuit.
This
reduces voltage errors caused by resistive losses across
the traces.
Route noise sensitive traces, such as the voltage feed-
back path, away from noisy traces between the power
components.
The voltage feedback trace must remain
close to the LM3671 circuit and should be direct but
should be routed opposite to noisy components. This
reduces EMI radiated onto the DC-DC converter’s own
voltage feedback trace. A good approach is to route the
feedback trace on another layer and to have a ground
plane between the top layer and layer on which the
feedback trace is routed. In the same manner for the
adjustable part it is desired to have the feedback divid-
ers on the bottom layer.
Place noise sensitive circuitry, such as radio IF blocks,
away from the DC-DC converter, CMOS digital blocks
and other noisy circuitry.
Interference with noise-
sensitive circuitry in the system can be reduced through
distance.
In mobile phones, for example, a common practice is to
place the DC-DC converter on one corner of the board,
arrange the CMOS digital circuitry around it (since this also
generates noise), and then place sensitive preamplifiers and
IF stages on the diagonally opposing corner. Often, the
sensitive circuitry is shielded with a metal pan and power to
it is post-regulated to reduce conducted noise, using low-
dropout linear regulators.
5.
6.
20108416
FIGURE 8. Board Layout Design Rules for the LM3671
L
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| LM3671MF-ADJ | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| LM3671MFX-1.2 | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| LM3671MFX-1.25 | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| LM3671MFX-1.375 | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
| LM3671MFX-1.5 | 2MHz , 600mA Step-Down DC-DC Converter in SOT23-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM3671MF-2.5 | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM3671MF-2.5/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM3671MF-2.8 | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM3671MF-2.8/NOPB | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| LM3671MF-3.3 | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。