- 您現在的位置：買賣IC網 > PDF目錄377648 > LM75AD (NXP Semiconductors N.V.) Digital temperature sensor and thermal watchdog PDF資料下載
參數資料
| 型號： | LM75AD |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 工業控制 |
| 英文描述： | Digital temperature sensor and thermal watchdog |
| 封裝： | LM75AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 17, 2005,;LM75AD<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 17, 2005,;LM |
| 文件頁數： | 4/24頁 |
| 文件大?。?/td> | 137K |
| 代理商： | LM75AD |
LM75A_4
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 04 — 10 July 2007
4 of 24
NXP Semiconductors
LM75A
Digital temperature sensor and thermal watchdog
7.
Functional description
7.1 General operation
The LM75A uses the on-chip band gap sensor to measure the device temperature with
the resolution of 0.125
°
C and stores the 11-bit 2's complement digital data, resulted from
11-bit A-to-D conversion, into the device Temp register. This Temp register can be read at
any time by a controller on the I
2
C-bus. Reading temperature data does not affect the
conversion in progress during the read operation.
The device can be set to operate in either mode: normal or shutdown. In normal operation
mode, the temp-to-digital conversion is executed every 100 ms and the Temp register is
updated at the end of each conversion. In shutdown mode, the device becomes idle, data
conversion is disabled and the Temp register holds the latest result; however, the device
I
2
C-bus interface is still active and register write/read operation can be performed. The
device operation mode is controllable by programming bit B0 of the configuration register.
The temperature conversion is initiated when the device is powered-up or put back into
normal mode from shutdown.
In addition, at the end of each conversion in normal mode, the temperature data (or Temp)
in the Temp register is automatically compared with the overtemperature shutdown
threshold data (or Tos) stored in the Tos register, and the hysteresis data (or Thyst) stored
in the Thyst register, in order to set the state of the device OS output accordingly. The
device Tos and Thyst registers are write/read capable, and both operate with 9-bit
2's complement digital data. To match with this 9-bit operation, the Temp register uses
only the 9 MSB bits of its 11-bit data for the comparison.
The way that the OS output responds to the comparison operation depends upon the OS
operation mode selected by configuration bit B1, and the user-defined fault queue defined
by configuration bits B3 and B4.
In OS comparator mode, the OS output behaves like a thermostat. It becomes active
when the Temp exceeds the T
os
, and is reset when the Temp drops below the T
hyst
.
Reading the device registers or putting the device into shutdown does not change the
state of the OS output. The OS output in this case can be used to control cooling fans or
thermal switches.
In OS interrupt mode, the OS output is used for thermal interruption. When the device is
powered-up, the OS output is first activated only when the Temp exceeds the T
os
; then it
remains active indefinitely until being reset by a read of any register. Once the OS output
has been activated by crossing T
os
and then reset, it can be activated again only when the
Temp drops below the T
hyst
; then again, it remains active indefinitely until being reset by a
read of any register. The OS interrupt operation would be continued in this sequence:
T
os
trip, Reset, T
hyst
trip, Reset, T
os
trip, Reset, T
hyst
trip, Reset, etc.
A1
A0
V
CC
6
7
8
Digital input. User-defined address bit 1.
Digital input. User-defined address bit 0.
Power supply.
Table 3.
Symbol
Pin description
…continued
Pin
Description
相關PDF資料 |
PDF描述 |
|---|---|
| LM75ADP | Digital temperature sensor and thermal watchdog |
| LM75AD | Digital temperature sensor and thermal watchdog |
| LM75BD | Digital temperature sensor and thermal watchdog |
| LM75BDP | Digital temperature sensor and thermal watchdog |
| LM75BGD | Digital temperature sensor and thermal watchdog |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM75AD,112 | 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC TS RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM75AD,118 | 功能描述:板上安裝溫度傳感器 I2C LOCAL +/- 2OC TS RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| LM75AD.112 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital temperature sensor and thermal watchdog |
| LM75AD/G-T | 功能描述:IC I2C TEMP SNSR/WATCHDOG 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓?fù)?ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| LM75AD112 | 制造商:Rochester Electronics LLC 功能描述: 制造商:NXP 功能描述: 制造商:NXP Semiconductors 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。