- 您現在的位置：買賣IC網 > PDF目錄361036 > LM9833CCVJD (NATIONAL SEMICONDUCTOR CORP) LM9833 48-Bit Color, 1200dpi USB Image Scanner PDF資料下載
參數資料
| 型號： | LM9833CCVJD |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | LM9833 48-Bit Color, 1200dpi USB Image Scanner |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封裝： | PLASTIC, TQFP-100 |
| 文件頁數： | 38/42頁 |
| 文件大?。?/td> | 547K |
| 代理商： | LM9833CCVJD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁
38
www.national.com
14.0 QUESTIONS AND ANSWERS
Q Where is calibration done
A Calibration is done on the host computer.
Q Does the LM9833 support 800dpi sensors 400dpi XXXdpi
A Yes. The LM9833 will support any sensor up to a maximum of
16383 pixels x 3 colors. Available horizontal resolutions are
calculated by the optical resolution of the scanner divided by
the HDPI_divider.
15.0 GENERAL NOTES AND TROUBLESHOOTING TIPS
(mclk_divider)(HDPI_divider)(ITA) must be greater than or equal
to 6. If this condition is not met, the LM9833 will not work.
Make sure the gamma tables are programmed with a valid
gamma curve.
Make sure the multiplier gain coefficients are loaded and correct.
(Remember, a gain coefficient of 0 means a GAIN of x0, not x1. If
the gain coefficient = 0 the output code will always be 0.)
Remember that when the LM9833 is reset (reg08 = 0x20) or in
suspend for longer than a few milliseconds (consult your DRAM
datasheet), DRAM refresh will stop and the Gamma and Coeffi-
cient data may be corrupted.
Some of the CCD signals (RS, CP1, and CP2) can have a small
pulse when line_end occurs. Line_end resets these signals and
depending on how they are programmed to go on and off,
line_end can chop off the signal before its programmed off time.
This is not a problem because the truncation occurs at the end of
every line, after all the image data for that line has been digitized.
Registers 4 and 5 only autowrap to 0 from their highest possible
legal address. If an address higher than the highest legal address
is written, it will continue to increment from the illegal address, not
wrap to 0, and unknown operation may occur. This can not hap-
pen unless the host writes an illegal address to the dataport.
The absolute distance between reference sample and signal
sample must be 2 MCLKs or greater, whether CDS is on or off.
The range of values for the Optical Black (registers 0F and 10),
Reset Pulse (11 and 12), CP1 pulse (13 and 14), CP2 pulse (15
and 16), Reference Sample (17), and Signal Sample (18) settings
depend on the rate of the pixel data coming from the sensor.
Always make sure line length (data pixels end - data pixels start)
is >= the horizontal divider. For example, if you are dividing by 12,
the line length must be >=12.
The Line End (registers 20 and 21) setting must be programmed
as follows relative to the Data Pixels End (registers 24 and 25)
setting:
Line End must be >= Data Pixels End + 20
The Data Pixels Start (registers 22 and 23) setting must be >=the
Active Pixels Start (registers 1E and 1F) setting.
The correct Default Phase Difference (registers 51, 52, and 53)
must be set for a scan to restart properly following a pause in the
scanning. See the LM9833 software for information on setting the
DPD register.
The number of fullsteps skipped at the start of a scan may be one
less than the Fullsteps to Skip at Start of Scan (registers 4A and
4B) setting.
The Scanning Step Size (registers 46 and 47) and Fast Feed
Step Size (registers 48 and 49) settings must be > 2.
When reverse is enabled, the LM9833 always stops on Red (line
rate color). When reverse is disabled, it will stop on any color.
The contents of register 01 is not reset by the start of a new scan,
but it is updated to the correct value after the first line has been
scanned. To reset this counter prior to starting a scan, the chip
can be briefly reset (register 7 = 0x20). Since resetting the chip
may have undesired consequences (turning the lamp off briefly,
interrupting DRAM refresh), it is also acceptable to simply wait
until register 01 starts incrementing. At that point the register 01
data will be correct.
Gamma and gain/offset coefficient data should be written with
reg07=0 (idle).
When configured to do so, changes on the Paper Sense and
MISC I/O pins were supposed to generate USB Interrupts. This
functionality is not working at the time of this datasheet’s publica-
tion. The solution (as demonstrated in our Twain Driver software)
is to poll register 02 every 200 to 500ms. This uses very little
additional bandwidth compared to the USB interrupt solution.
Paper Sensor #2 Doesn’t Stop Sensor When Homing: See Sec-
tion
12.16
.
Mode
Pixel Rate
Registers 0F to 18
Range
Pixel Rate Modes
MCLK/24
0 - 23
Line Rate Modes
MCLK/8
0 - 7
stepsize_ITA
stepsize
-----------
=
Applications Information
(Continued)
L
相關PDF資料 |
PDF描述 |
|---|---|
| LM9833 | LM9833 48-Bit Color, 1200dpi USB Image Scanner |
| LM98501CCVBH | 10-Bit, 27 MSPS Camera Signal Processor |
| LM98501 | 10-Bit, 27 MSPS Camera Signal Processor |
| LMC555CBPEVAL | CMOS Timer |
| LMC555CN | CMOS Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM9833CCVJD NOPB | 制造商:Texas Instruments 功能描述:Bulk |
| LM9833CCVJD/NOPB | 功能描述:視頻模擬/數字化轉換器集成電路 RoHS:否 制造商:Texas Instruments 輸入信號類型:Differential 轉換器數量:1 ADC 輸入端數量:4 轉換速率:3 Gbps 分辨率:8 bit 結構: 輸入電壓:3.3 V 接口類型:SPI 信噪比: 電壓參考: 電源電壓-最大:3.45 V 電源電壓-最小:3.15 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:TCSP-48 封裝:Reel |
| LM98501 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-Bit, 27 MSPS Camera Signal Processor |
| LM98501A WAF | 制造商:Texas Instruments 功能描述: |
| LM98501CCVBH | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:10-Bit, 27 MSPS Camera Signal Processor |
發布緊急采購，3分鐘左右您將得到回復。