- 您現在的位置：買賣IC網 > PDF目錄10677 > LT1721IS#PBF (Linear Technology)IC COMP R-RINOUT QUAD 16-SOIC PDF資料下載
參數資料
| 型號： | LT1721IS#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 2/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC COMP R-RINOUT QUAD 16-SOIC |
| 標準包裝： | 50 |
| 系列： | UltraFast™ |
| 類型： | 通用 |
| 元件數： | 4 |
| 輸出類型： | CMOS，滿擺幅，TTL |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 6 V |
| 電壓 - 輸入偏移（最小值）： | 3mV @ 5V |
| 電流 - 輸入偏壓（最小值）： | 6µA @ 5V |
| 電流 - 輸出（標準）： | 20mA |
| 電流 - 靜態（最大值）： | 7mA |
| CMRR, PSRR（標準）： | 70dB CMRR，80dB PSRR |
| 傳輸延遲（最大）： | 10ns |
| 磁滯： | 7mV |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 安裝類型： | 表面貼裝 |
| 包裝： | 管件 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LT1720/LT1721
10
17201fc
The exact amount of hysteresis will vary from part to part
as indicated in the specications table. The hysteresis level
will also vary slightly with changes in supply voltage and
common mode voltage. A key advantage of the LT1720/
LT1721 is the signicant reduction in these effects, which
is important whenever an LT1720/LT1721 is used to detect
a threshold crossing in one direction only. In such a case,
the relevant trip point will be all that matters, and a stable
offset voltage with an unpredictable level of hysteresis,
as seen in competing comparators, is of little value. The
LT1720/LT1721 are many times better than prior compara-
tors in these regards. In fact, the CMRR and PSRR tests are
performed by checking for changes in either trip point to
the limits indicated in the specications table. Because the
offset voltage is the average of the trip points, the CMRR
and PSRR of the offset voltage is therefore guaranteed to
be at least as good as those limits. This more stringent
test also puts a limit on the common mode and power
supply dependence of the hysteresis voltage.
Additional hysteresis may be added externally. The
rail-to-rail outputs of the LT1720/LT1721 make this more
predictable than with TTL output comparators due to the
LT1720/LT1721’s small variability of VOH (output high
voltage).
To add additional hysteresis, set up positive feedback
by adding additional external resistor R3 as shown in
Figure 3. Resistor R3 adds a portion of the output to the
threshold set by the resistor string. The LT1720/LT1721
pulls the outputs to the supply rail and ground to within
200mV of the rails with light loads, and to within 400mV
with heavy loads. For the load of most circuits, a good
APPLICATIONS INFORMATION
model for the voltage on the right side of R3 is 300mV or
VCC – 300mV, for a total voltage swing of (VCC – 300mV)
– 300mV = VCC – 600mV.
With this in mind, calculation of the resistor values needed
is a two-step process. First, calculate the value of R3 based
on the additional hysteresis desired, the output voltage
swing, and the impedance of the primary bias string:
R3 = (R1 || R2)(VCC – 0.6V)/(additional hysteresis)
Additional hysteresis is the desired overall hysteresis less
the internal 3.5mV hysteresis.
The second step is to recalculate R2 to set the same av-
erage threshold as before. The average threshold before
was set at VTH = (VREF)(R1)/(R1 + R2). The new R2 is
calculated based on the average output voltage (VCC/2)
and the simplied circuit model in Figure 4. To assure
that the comparator’s noninverting input is, on average,
the same VTH as before:
R2
′ = (VREF – VTH)/(VTH/R1 + (VTH – VCC/2)/R3)
For additional hysteresis of 10mV or less, it is not
uncommon for R2
′ to be the same as R2 within 1%
resistor tolerances.
This method will work for additional hysteresis of up to
a few hundred millivolts. Beyond that, the impedance of
R3 is low enough to effect the bias string, and adjust-
ment of R1 may also be required. Note that the currents
through the R1/R2 bias string should be many times the
input currents of the LT1720/LT1721. For 5% accuracy,
the current must be at least 120μA(6μA IB ÷ 0.05); more
for higher accuracy.
Figure 3. Additional External Hysteresis
–
+
1/2 LT1720
INPUT
17201 F03
R2
VREF
R3
R1
Figure 4. Model for Additional Hysteresis Calculations
–
+
1/2 LT1720
17201 F04
R2
VREF
VTH
R3
VCC
2
VAVERAGE =
R1
相關PDF資料 |
PDF描述 |
|---|---|
| LT1721CGN | IC COMP R-RINOUT QUAD 16-SSOP |
| VI-J2Z-MY-F1 | CONVERTER MOD DC/DC 2V 20W |
| ADCMP580BCPZ-RL7 | IC COMPARATOR CML UFAST 16-LFCSP |
| DS90CF363BMT/NOPB | IC FPD-LINK TX 18BIT 48-TSSOP |
| VI-B3K-MY-B1 | CONVERTER MOD DC/DC 40V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT1722 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Single, Dual, Quad 200MHz Low Noise Precision Op Amps |
| LT1722CS5 | 制造商:Linear Technology 功能描述:OP Amp Single GP ±6.3V/12.6V 5-Pin TSOT-23 |
| LT1722CS5#PBF | 制造商:Linear Technology 功能描述:OP Amp Single GP 制造商:Linear Technology 功能描述:SC-Amps/Industrial Cut Tape 2 制造商:Linear Technology 功能描述:SC-Amps/Industrial, Cut Tape 200MHz Low Noise Precision OP Amp |
| LT1722CS5#TR | 功能描述:IC OPAMP PREC 200MHZ TSOT-23-5 RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:160 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:10 V/µs 增益帶寬積:9MHz -3db帶寬:- 電流 - 輸入偏壓:1pA 電壓 - 輸入偏移:250µV 電流 - 電源:730µA 電流 - 輸出 / 通道:28mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 5.5 V，±1.35 V ~ 2.75 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC N 包裝:管件 |
| LT1722CS5#TRM | 功能描述:IC OPAMP PREC 200MHZ TSOT-23-5 RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):7 V ~ 36 V，±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP（0.300"，7.62mm） 供應商設備封裝:8-PDIP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。