- 您現在的位置：買賣IC網 > PDF目錄377745 > LTC1407 (Linear Technology Corporation) Serial 12-Bit/14-Bit, 3Msps Simultaneous Sampling Simultaneous Sampling PDF資料下載
參數資料
| 型號： | LTC1407 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Serial 12-Bit/14-Bit, 3Msps Simultaneous Sampling Simultaneous Sampling |
| 中文描述： | 串行12-Bit/14-Bit，3Msps同步采樣同步采樣 |
| 文件頁數： | 14/24頁 |
| 文件大?。?/td> | 443K |
| 代理商： | LTC1407 |
14
LTC1407/LTC1407A
1407f
High quality tantalum and ceramic bypass capacitors should
be used at the V
DD
and V
REF
pins as shown in the Block
Diagram on the first page of this data sheet. For optimum
performance, a 10
μ
F surface mount tantalum capacitor
with a 0.1
μ
F ceramic is recommended for the V
DD
and V
REF
pins. Alternatively, 10
μ
F ceramic chip capacitors such as
X5R or X7R may be used. The capacitors must be located
as close to the pins as possible. The traces connecting the
pins and the bypass capacitors must be kept short and
should be made as wide as possible. The V
DD
bypass ca-
pacitor returns to GND (Pin 6) and the V
REF
bypass capaci-
tor returns to the Exposed Pad ground (Pin 11). Care should
be taken to place the 0.1
μ
F V
DD
bypass capacitor as close
to Pins 6 and 7 as possible.
Figure 5 shows the recommended system ground connec-
tions. All analog circuitry grounds should be terminated at
the LTC1407/LTC1407A Exposed Pad. The ground return
from the LTC1407/LTC1407A Pin 6 to the power supply
should be low impedance for noise-free operation. The
Exposed Pad of the 10-lead MSE package is also tied to
Pin6 and the LTC1407/LTC1407A GND. The Exposed Pad
should be soldered on the PC board to reduce ground
connection inductance. Digital circuitry grounds must be
connected to the digital supply common.
APPLICATIOU
Integral nonlinearity errors (INL) and differential nonlin-
earity errors (DNL) are largely independent of the common
mode voltage. However, the offset error will vary. CMRR
is typically better than 60dB.
Figure 4 shows the ideal input/output characteristics for
the LTC1407/LTC1407A. The code transitions occur mid-
way between successive integer LSB values (i.e., 0.5LSB,
1.5LSB, 2.5LSB, FS – 1.5LSB). The output code is natural
binary with 1LSB = 2.5V/16384 = 153
μ
V for the LTC1407A
and 1LSB = 2.5V/4096 = 610
μ
V for the LTC1407. The
LTC1407A has 1LSB RMS of Gaussian white noise.
W
U
U
Board Layout and Bypassing
Wire wrap boards are not recommended for high resolu-
tion and/or high speed A/D converters. To obtain the best
performance from the LTC1407/LTC1407A, a printed cir-
cuit board with ground plane is required. Layout for the
printed circuit board should ensure that digital and analog
signal lines are separated as much as possible. In particu-
lar, care should be taken not to run any digital track
alongside an analog signal track. If optimum phase match
between the inputs is desired, the length of the four input
wires of the two input channels should be kept matched.
But each pair of input wires to the two input channels
should be kept separated by a ground trace to avoid high
frequency crosstalk between channels.
INPUT VOLTAGE (V)
1407 F04
111...111
111...110
111...101
000...000
000...001
000...010
FS – 1LSB
0
Figure 4. LTC1407/LTC1407A Transfer Characteristic
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1407A | Serial 12-Bit/14-Bit, 3Msps Simultaneous Sampling Simultaneous Sampling |
| LTC1407AIMSE | Serial 12-Bit/14-Bit, 3Msps Simultaneous Sampling Simultaneous Sampling |
| LTC1407IMSE | Serial 12-Bit/14-Bit, 3Msps Simultaneous Sampling Simultaneous Sampling |
| LTC1409C | 12-Bit, 800ksps Sampling A/D Converter with Shutdown |
| LTC1409IG | 12-Bit, 800ksps Sampling A/D Converter with Shutdown |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1407ACMSE | 功能描述:IC ADC 14BIT 3MSPS SAMPLE 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1407ACMSE#PBF | 功能描述:IC ADC 14BIT 3MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1407ACMSE#TR | 功能描述:IC ADC 14BIT 3MSPS SAMPLE 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1407ACMSE#TRPBF | 功能描述:IC ADC 14BIT 3MSPS SAMPLE 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1407ACMSE-1 | 功能描述:IC ADC 14BIT 3MSPS SAMPLE 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。