參數資料
型號： LTC1955EUH#TR
廠商： Linear Technology
文件頁數： 4/22頁
文件大?。?/td> 0K
描述： IC SMART CARD INTERFC DUAL 32QFN
標準包裝： 2,500
控制器類型： 智能卡接口
接口： 4 線串行
電源電壓： 1.7 V ~ 5.5 V
電流 - 電源： 10µA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 32-WFQFN 裸露焊盤
供應商設備封裝： 32-QFN 裸露焊盤（5x5）
包裝： 帶卷 (TR)
LTC1955
12
1955fd
For more information www.linear.com/LTC1955
Smart Card Detection Circuits
The PRES A/PRES B pins are used to detect the presence
of a smart card. An automatic debounce circuit waits until
a smart card has been present for a continuous period
of typically 35ms. Once a valid card indication exists,
the status bit for that channel is updated and may be
polled by cycling data through the serial port. The DOUT
pin (equivalent to D15) of the serial port can be used to
indicate the presence of a card on channel A in real time
if LD is held low.
The PRES A/PRES B pins have built-in pull-up current
sources, so no external components are required for
switchdetection.Thepull-upcurrentsourcesaredesigned
to have a small current when the pin voltage is below ap-
proximately 1V, but somewhat higher current when the
pin voltage reaches 1V. This helps maintain low power
dissipation when a card is present and yet fast response
time to a card removal.
The PRES A/PRES B pins can be configured to respond
to either normally open or normally closed switches via
the NC/NO pin.
Activation/Deactivation
For maximum flexibility, the activation sequencing of the
smart card is left to the application programmer. Upon
activation, to comply with relevant smart card standards,
none of the smart card signal pins will be allowed to go
highbeforethesmartcardsupplyvoltage(VCCA/VCCB)has
reached its final value. Deactivation can be achieved either
manually or automatically. An electrical fault condition will
trigger the automatic deactivation.
Manual deactivation may be performed under software
control by setting the smart card pins to 0V in the desired
sequence via the control pins (SYNC, ASYNC, RIN, DATA
and the serial port). For most applications, this will be
cumbersome and the built-in deactivation will be used
instead.
Automatic Deactivation
The built-in deactivation sequence can be executed via the
serial port simply by setting the appropriate control bits
(D0 and D1 or D8 and D9) to 0. The deactivation sequence
is outlined below.
1. The RST A/RST B pin for that channel is immediately
brought low.
2. The deactivation of the CLK A/CLK B pins depends upon
which type of card is used:
If the smart card was set to asynchronous mode, then
the CLK A/CLK B pin will be latched low on its next
falling edge. If no falling edges occur within 5s (min),
then the CLK A/CLK B line is forced low.
Ifthesmartcardwassettosynchronousmode,thenthe
CLK A/CLK B pin is immediately latched at its current
value (either high or low) and then forced low after a
duration of 5s (min). During the 5s timeout period,
changes on SYNC will be ignored.
3. The I/O A/I/O B, C4A and C8A pins for that channel are
brought low.
4. The VCCA/VCCB pin is brought low.
If an error occurs on one smart card, operation of the
other card is unaffected.
Electrical Fault Detection
Several types of faults are detected by the LTC1955. They
include VCCA/VCCB undervoltage, VCCA/VCCB overcurrent,
CLK A/CLK B, RST A/RST B, C8A, C4A short-circuit, card
removalduringatransaction,failedanswertoreset(ATR),
supplyundervoltageorUNDERVandchipovertemperature.
To prevent false errors from plaguing the microcontroller,
the electrical faults are acted upon only after a 5s (min)
timeout period. Card removal during transaction faults
initiate the deactivation sequence immediately.
operaTion
相關PDF資料
PDF描述
VE-26B-CV-S CONVERTER MOD DC/DC 95V 150W
LTC4267IGN#TRPBF IC POE 802.3AF INTERFACE 16SSOP
LTC4267CGN#PBF IC POE 802.3AF INTERFACE 16SSOP
LTC4267CDHC#TRPBF IC POE 802.3AF INTERFACE 16-DFN
LTC4267CGN#TRPBF IC POE 802.3AF INTERFACE 16SSOP
相關代理商/技術參數
參數描述
LTC1955IUH#PBF 功能描述:IC SMART CARD INTERFACE DL 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC1955IUH#TRPBF 功能描述:IC SMART CARD INTERFACE DL 32QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC1957-1EMS8 功能描述:IC RF PWR CONTRLLR SINGLE 8-MSOP RoHS:否 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX
LTC1957-1EMS8#PBF 功能描述:IC RF PWR CONTRLLR SINGLE 8-MSOP RoHS:是 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX
LTC1957-1EMS8#TR 功能描述:IC RF PWR CONTRLLR SINGLE 8-MSOP RoHS:否 類別:RF/IF 和 RFID >> RF 電源控制器 IC 系列:- 標準包裝:3,000 系列:- RF 型:GSM 頻率:450MHz ~ 2GHz 特點:四頻帶 封裝/外殼:8-VFBGA 供應商設備封裝:8-MicroSMD（1.51x1.51） 包裝:帶卷 (TR) 其它名稱:LMV243BLX
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*