參數資料
型號： LTC2264IUJ-12#TRPBF
廠商： Linear Technology
文件頁數： 18/34頁
文件大小： 0K
描述： IC ADC 12BIT SER/PAR 40M 40-QFN
標準包裝： 2,000
位數： 12
采樣率（每秒）： 40M
數據接口： Serial LVDS
轉換器數目： 2
功率耗散（最大）： 169mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 40-WFQFN 裸露焊盤
供應商設備封裝： 40-QFN（6x6）
包裝： 帶卷 (TR)
輸入數目和類型： 2 Differential; 2 Single-Ended
配用： DC1371A-ND - BOARD USB DATA ACQUISITION HS
LTC2265-12/
LTC2264-12/LTC2263-12
25
22654312fb
APPLICATIONS INFORMATION
Digital Output Randomizer
Interference from the A/D digital outputs is sometimes
unavoidable.Digitalinterferencemaybefromcapacitiveor
inductive coupling or coupling through the ground plane.
Even a tiny coupling factor can cause unwanted tones
in the ADC output spectrum. By randomizing the digital
output before it is transmitted off chip, these unwanted
tones can be randomized which reduces the unwanted
amplitude.
The digital output is randomized by applying an exclu-
sive-OR logic operation between the LSB and all other
data output bits. To decode, the reverse operation is
applied—an exclusive-OR operation is applied between
the LSB and all other bits. The FR and DCO outputs are
not affected. The output randomizer is enabled by serially
programming mode control register A1.
Digital Output Test Pattern
To allow in-circuit testing of the digital interface to the
A/D, there is a test mode that forces the A/D data outputs
(D11-D0, DX, DY) of all channels to known values. The
digitaloutputtestpatternsareenabledbyseriallyprogram-
ming mode control registers A3 and A4. When enabled,
the test patterns override all other formatting modes: 2’s
complement and randomizer.
Output Disable
The digital outputs may be disabled by serially program-
ming mode control register A2. The current drive for all
digital outputs, including DCO and FR, are disabled to save
powerorenablein-circuittesting.Whendisabled,thecom-
mon mode of each output pair becomes high impedance,
but the differential impedance may remain low.
Sleep and Nap Modes
The A/D may be placed in sleep or nap modes to conserve
power. In sleep mode the entire chip is powered down,
resulting in 1mW power consumption. Sleep mode is
enabled by mode control register A1 (serial program-
ming mode), or by SDI (parallel programming mode).
The amount of time required to recover from sleep mode
depends on the size of the bypass capacitors on VREF,
REFH and REFL. For the suggested values in Figure 8, the
A/D will stabilize after 2ms.
In nap mode any combination of A/D channels can be
powered down while the internal reference circuits and the
PLL stay active, allowing faster wake-up than from sleep
mode. Recovering from nap mode requires at least 100
clockcycles.IftheapplicationdemandsaveryaccurateDC
settling, then an additional 50s should be allowed so the
on-chip references can settle from the slight temperature
shift caused by the change in supply current as the A/D
leavesnapmode.Napmodeisenabledbythemodecontrol
register A1 in the serial programming mode.
DEVICE PROGRAMMING MODES
The operating modes of the LTC2265-12/LTC2264-12/
LTC2263-12 can be programmed by either a parallel
interface or a simple serial interface. The serial interface
has more flexibility and can program all available modes.
Theparallelinterfaceismorelimitedandcanonlyprogram
some of the more commonly used modes.
Parallel Programming Mode
To use the parallel programming mode, PAR/SER should
be tied to VDD. The CS, SCK, SDI and SDO pins are binary
logic inputs that set certain operating modes. These pins
can be tied to VDD or ground, or driven by 1.8V, 2.5V or
3.3V CMOS logic. When used as an input, SDO should
be driven through a 1k series resistor. Table 3 shows the
modes set by CS, SCK, SDI and SDO.
Table 3. Parallel Programming Mode Control Bits (PAR/SER = VDD)
PIN
DESCRIPTION
CS
2-Lane/1-Lane Selection Bit
0 = 2-Lane, 16-Bit Serialization Output Mode
1 = 1-Lane, 14-Bit Serialization Output Mode
SCK
LVDS Current Selection Bit
0 = 3.5mA LVDS Current Mode
1 = 1.75mA LVDS Current Mode
SDI
Power Down Control Bit
0 = Normal Operation
1 = Sleep Mode
SDO
Internal Termination Selection Bit
0 = Internal Termination Disabled
1 = Internal Termination Enabled
相關PDF資料
PDF描述
MS27484P16B26P CONN PLUG 26POS STRAIGHT W/PINS
VE-241-IU-F3 CONVERTER MOD DC/DC 12V 200W
LTC1419CG#PBF IC A/D CONV 14BIT SAMPLNG 28SSOP
MS27473T14B97PA CONN PLUG 12POS STRAIGHT W/PINS
MS3102C22-23P CONN RCPT 8POS BOX MNT W/PINS
相關代理商/技術參數
參數描述
LTC2264IUJ-14 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65Msps/40Msps/25Msps Low Power Dual ADCs
LTC2264IUJ-14#PBF 功能描述:IC ADC 14BIT SER/PAR 40M 40-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
LTC2264IUJ-14#TRPBF 功能描述:IC ADC 14BIT SER/PAR 40M 40-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
LTC2264IUJ-14PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65Msps/40Msps/25Msps Low Power Dual ADCs
LTC2264IUJ-14TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65Msps/40Msps/25Msps Low Power Dual ADCs
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*