- 您現在的位置：買賣IC網 > PDF目錄377777 > LTC4216 (Linear Technology Corporation) Ultralow Voltage Hot Swap Controller PDF資料下載
參數資料
| 型號： | LTC4216 |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Ultralow Voltage Hot Swap Controller |
| 中文描述： | 超低電壓熱插拔控制器 |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 277K |
| 代理商： | LTC4216 |
LTC4216
11
Analog Current Limiting
In addition to an electronic circuit breaker, the LTC4216
has included a novel analog current limit (ACL) amplifier
that does not require an external compensation capacitor
at the GATE pin. The amplifier’s stability is compensated
by the large gate input capacitance (C
ISS
) of the external
MOSFET used. These MOSFETs usually have C
ISS
≥ 1nF.
However, if the MOSFET’s gate input capacitance (C
ISS
)
is too small for loop stability, then connect an external
capacitor between the GATE pin and ground to increase
the total gate capacitance to ≥ 1nF. As given by Equation
(4), the MOSFET current, I
ACL
, is limited to the analog
current limit voltage,
Δ
V
ACL(TH)
, 40mV typical, across
the sense resistor, R
SENSE
, connected between SENSEP
and SENSEN pins.
The
Δ
V
ACL(TH)
threshold is 1.6 times higher than the
Δ
V
CB(TH)
threshold (25mV typical) to provide dual level cur-
rent sensing. When the ACL amplifier servos the MOSFET
current at
Δ
V
ACL(TH)
across the sense resistor, it exceeds
Δ
V
CB(TH)
threshold causing the FILTER pin to charge C3
with 60μA pull-up. If the condition persists long enough
for C3 to reach the V
FILT(TH)
threshold (1.253V), GATE is
pulled low and
F
A
U
L
T latched low.
I
V
R
ACL
ACL TH
SENSE
=
(
)
(4)
If the voltage across the sense resistor is greater than
Δ
V
ACL(TH)
during an overload condition, the ACL amplifier
will servo GATE downwards in an attempt to control the
MOSFET current. Since the GATE pin voltage overdrives
the MOSFET in normal operation, the ACL amplifier needs
time to discharge the GATE to the threshold of the MOSFET
for gate regulation. For mild overload, the ACL amplifier
can control the MOSFET current, but in the event of a
severe overload, the MOSFET current may overshoot as
the MOSFET has large GATE overdrive initially. The GATE
is quickly discharged to ground followed by the ACL ampli-
fier taking control. For applications that require very fast
analog current limit recovery from the GATE undershoot as
it discharges, connect a series resistor, R
Z
, with an external
capacitor, C
Z
, at the GATE pin as shown in Figure 17.
Soft-Start
The LTC4216 features a soft-start function that controls
the di/dt of the inrush current during power-up. As large
output load capacitors are commonly used in low-voltage
applications, the normal inrush can be large enough to
glitch the load supply. With the soft-start function, the
gate of the external MOSFET is allowed to turn on very
gradually to control the inrush current flowing into the
load capacitor without causing a supply glitch.
With an external capacitor, C2, connected between the SS
pin and ground, the GATE is servoed by the ACL amplifier
to track the rate of SS ramp-up during power-up. There
are two slopes in the SS ramp-up profile: 10μA current
source pull-up for a normal ramp rate; and 1μA current
source pull-up for a slower ramp rate. Both the SS ramp
rates are given as follows:
Normal SS Ramp Rate:
dV
dt
A
C
SS NOM
(
)
=
μ
2
(5)
10
Slower SS Ramp Rate:
dV
dt
A
2
C
SS SLOW
(
)
=μ
1
(6)
Figure 6. Circuit Breaker Filter
Response for Intermittent Overload
APPLICATIU
W
U
U
OVERLOAD DUTY CYCLE, D (%)
0
20
40
60
80
100
N
μ
F
1
0.1
0.01
4216 F06
t/C3(s/
μ
F) = 1.253/[(60 D) – 2.4]
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4221CGN | Dual Hot Swap Controller/ Power Sequencer with Dual Speed, Dual Level Fault Protection |
| LTC4221IGN | Dual Hot Swap Controller/ Power Sequencer with Dual Speed, Dual Level Fault Protection |
| LTC4221 | Dual Hot Swap Controller/ Power Sequencer with Dual Speed, Dual Level Fault Protection |
| LTC4240 | CompactPCI Hot Swap Controller with I2C Compatible Interface |
| LTC4240IGN | CompactPCI Hot Swap Controller with I2C Compatible Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4216CDE | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 6V 12-Pin DFN EP |
| LTC4216CDE#PBF | 功能描述:IC CTLR HOT SWAP 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4216CDE#TR | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 6V 12-Pin DFN EP T/R |
| LTC4216CDE#TRPBF | 功能描述:IC CNTRLR HOT SWAP 12-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4216CMS | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Ultralow Voltage Hot Swap Controller |
發布緊急采購，3分鐘左右您將得到回復。