參數資料
型號： LTC4259A
廠商： Linear Technology Corporation
英文描述： Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect
中文描述： 四IEEE 802.3af標準與AC電源斷開以太網控制器
文件頁數： 22/32頁
文件大?。?/td> 326K
代理商： LTC4259A
LTC4259A
22
4259Af
OSCIN Input and Oscillator Requirements
AC disconnect depends on an external oscillator source
applied to the OSCIN pin. The LTC4259A measures port
impedance by applying an amplified version of the OSCIN
signal to the port’s DETECT pin (see Figure 16). The
oscillator should be well-controlled because errors in this
signal become errors in the measured port impedance. As
shown in Figure 17, the load being sensed by AC discon-
nect has a resistive and a large reactive component.
Current through the PD’s signature resistor depends on
the amplitude of the AC signal while current into the
capacitors depends on the slew rated: I = C dV/dt.
Consequently, the LTC4259A is sensitive to the amplitude
and slew rate of the OSCIN signal, but is more tolerant of
frequency and offset errors. Internal limits prevent the
LTC4259A from being adversely affected by OSCIN sig-
nals with excessive amplitude.
There are many ways to build oscillators with controlled
amplitudes and slew rates, especially since the frequency
of the oscillator does not have to be well-controlled.
Contact the LTC Applications department for oscillator
circuits.
As alluded to previously, AC disconnect is complicated
and redesigning for different component sizes is a difficult
task. For optimum performance, use the recommended
component values and drive OSCIN with a 100Hz 2V
P-P
,
1.2V offset sine wave. Keep in mind that the IEEE 802.3af
specification places upper limits of 100V/ms on the slew
rate and 500Hz on the frequency of the AC signal at the
port. Voltage gain, A
VACD
, from OSCIN to DETECTnin-
creases the slew rate by the voltage gain. Since A
VACD
has
a maximum absolute value of 3.3V/V (
±
3V typ), the slew
rate at the OSCIN pin must be less than 30V/ms. A slew
rate around 0.6V/ms at OSCIN will work with the recom-
mended values of C
DET
, R
DET
and C
PSE
.
The LTC4259A’s OSCIN input amplifier will accept signals
between DGND – 0.3V and V
DD
+ 0.5V. This amplifier has
a gain of –1 and is referenced to 1.2V above DGND. An
OSCIN voltage greater than 2.2V will cause the amplifier’s
output to clip against DGND. Clipping will not affect the
performance of AC disconnect until the clipping becomes
so severe that even the midrange (where the controlled
slew rate occurs) of the signal is clipped. Keep the midrange
or average voltage of the OSCIN signal between 0.9V and
1.5V to avoid severe clipping. OSCIN signals below DGND
can interact with the ESD protection circuitry on the pin
and are not recommended. Also, meeting the IEEE 802.3af
specification for maximum AC amplitude on the port just
after the PD is removed depends on the OSCIN input peak-
to-peak amplitude. Clipping by LTC4259A’s OSCIN input
circuitry will generally ensure that this specification is not
exceeded. Note that under normal operation, the AC dis-
connect output on the DETECTnpin will have an amplitude
near 6V peak-to-peak. The combination of R
DET
, C
DET
and
C
PSE
attenuate the signal so roughly half this amplitude is
seen at the port when the port is powered and the PD has
just been removed. When the PD is still connected there
will be almost no AC signal at the port.
The LTC4259A monitors Pin 36 for the presence of an
oscillating signal. If no signal is present and the Osc Fail
Mask bit is set, then Osc Fail (bit 1 of the Supply Event
register) is set, triggering an interrupt. As the LTC4259A’s
AC disconnect circuitry self-checks the OSCIN signal, the
Osc Fail bit is intended as a fault indicator to alert the PSE
host controller. The Osc Fail bit has no effect beyond
triggering the interrupt. A clear Osc Fail bit indicates that
the OSCIN signal goes below 0.6V and above 1.8V at least
once every 250ms. It does not necessarily guarantee that
AC disconnect will function properly. However, AC discon-
nect itself is a more thorough test of the OSCIN signal.
When the OSCIN signal is either absent or corrupted,
powered ports with AC disconnect enabled (and DC dis-
connect not enabled) will automatically disconnect. After
the LTC4259A is reset (by power on, Reset All bit or the
RESET pin) the Osc Fail bit is set. Once the Osc Fail bit is
cleared, it will only be set by an invalid signal on the OSCIN
pin or another reset.
APPLICATIOU
W
U
U
相關PDF資料
PDF描述
LTC4259ACGW Quad IEEE 802.3af Power over Ethernet Controller with AC Disconnect
LTC4260 Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring
LTC4260CGN Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring
LTC4260CSW Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring
LTC4260CUH Positive High Voltage Hot Swap Controller with I2C Compatible Monitoring
相關代理商/技術參數
參數描述
LTC4259A-1 制造商:LINER 制造商全稱:Linear Technology 功能描述:Synchronous No-Opto Flyback Controller
LTC4259ACGW 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4259ACGW#PBF 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4259ACGW#TR 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
LTC4259ACGW#TRPBF 功能描述:IC CTRLR POE QUAD AC DISC 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:2,450 系列:- 控制器類型:SPI 總線至 I²C 總線橋接 接口:I²C，串行，SPI 電源電壓:2.4 V ~ 3.6 V 電流 - 電源:11mA 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-HVQFN（4x4） 包裝:托盤 配用:568-3511-ND - DEMO BOARD SPI TO I2C 其它名稱:935286452157SC18IS600IBSSC18IS600IBS-ND
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*