- 您現在的位置：買賣IC網 > PDF目錄367613 > LUCL8576BP-DT Dual Ringing SLIC PDF資料下載
參數資料
| 型號： | LUCL8576BP-DT |
| 英文描述： | Dual Ringing SLIC |
| 中文描述： | 雙振鈴用戶接口 |
| 文件頁數： | 24/26頁 |
| 文件大?。?/td> | 583K |
| 代理商： | LUCL8576BP-DT |
24
Agere Systems Inc.
Data Sheet
May 2001
L8576B Dual Ringing SLIC
Applications
(continued)
ac Design
(continued)
Typically, values of 0.1
μ
F to 0.47
μ
F capacitors are
used for dc blocking. The addition of blocking capaci-
tors will cause a shift in the return loss and hybrid bal-
ance frequency response toward higher frequencies,
degrading the lower-frequency response. The lower
the value of the blocking capacitor, the more pro-
nounced the effect is, but the cost of the capacitor is
lower. It may be necessary to scale resistor values
higher to compensate for the low-frequency response.
This effect is best evaluated via simulation. A PSPICE*
model for the L8576B is available.
Design equation calculations seldom yield standard
component values. Conversion from the calculated
value to standard value may have an effect on the ac
parameters. This effect should be evaluated and opti-
mized via simulation.
Use of an Auxiliary Battery Supply
A second lower-voltage battery supply can be used
with the L8576B in order to lower the overall power
consumption on a short-loop design. For long loops,
any power savings will be negated, since long loops
are supplied by the main battery voltage. The auxiliary
battery would be connected to pins 9 and 37 in lieu of
the R
PWR
resistors. When the external R
PWR
resistors
are removed, more power will be dissipated in the SLIC
so internal SLIC power dissipation must be examined.
First, determine the auxiliary battery voltage:
The auxiliary battery should be set 8 V greater than the
maximum tip/ring loop voltage on the longest allowed
loop, when both channels are off-hook and in current
limit.
Aux Bat
(MAX)
= [(I
LIM
x R
LOOP
) + V
OH
] TOL
VBAT
Where:
I
LIM
= dc current limit set by R
PROG
(usually 0.024).
R
LOOP
= maximum loop resistance supported (tele-
phone plus line resistance plus protection
resistors).
V
OH
= overhead voltage.
TOL
VBAT
= battery tolerance, for a battery tolerance of
±5%, use 1.1.
For example, using the recommended 24 mA current
limit, an overhead voltage of 8 V, and a maximum loop
length of 550
, the maximum auxiliary battery voltage
is 23.3 V.
Next, calculate the power dissipated in the SLIC:
Components of the SLIC power dissipation are quies-
cent power of V
CC
and V
BAT
and loop current associ-
ated with V
BAT
and Aux Bat. These can be calculated
as follows:
W
VCC(quiescent)
= V
CC
x I
CC(Max)(quiescent)
x 2 channels.
W
VBAT(quiescent)
= |V
BAT(Max)
| x I
BAT(Max)(quiescent)
x 2 chan-
nels.
W
VBAT(loop current)
= (|V
BAT(Max)
| – 4 V) x 3 mA x 2 chan-
nels.
W
Aux Bat(loop current)
= (|Aux Bat
(Max)
| – 4 V) x (I
LIM
– 3 mA)
x 2 channels.
Where:
4 V is the minimum overhead voltage, and 3 mA is
V
BAT
’s contribution to loop current.
For example, substituting values from the data sheet:
V
CC
= 5 V
I
CC(Max)(quiescent)
= 5.5 mA
V
BAT(Max)
= –70 V
I
BAT(Max)(quiescent)
= 4 mA
Aux Bat
(Max)
= –23.3 V
I
LIM
= 24 mA
The following powers are calculated:
W
VCC(quiescent)
= 5 x 0.0055 x 2 = 0.055
W
VBAT(quiescent)
= |–70| x 0.004 x 2 = 0.56
W
VBAT(loop current)
= (|–70| – 4) x 0.003 x 2 = 0.396
W
Aux Bat(loop current)
= (|–23.3| – 4) x (0.024 – 0.003) x 2 =
0.8106
The sum of the four powers is 1.822 W.
Finally, calculate the maximum ambient tempera-
ture allowed for the calculated power dissipation:
T
A(max)
= T
j
– (R
θ
JA
x P
DISS SLIC(max)
)
The L8576’s 44-pin PLCC exhibits a 43 °C/W thermal
resistance if in an enclosure with natural airflow. The
maximum operating temperature of the SLIC is 150 °C.
Thermal shutdown occurs typically at 160 °C.
For example:
T
A(max)
= 150 – (43 x 1.822)
= 150 – 78.4
= 71.7 °C
The above scenario would allow operation up to 70 °C.
* PSPICEis a registered trademark of Cadence Design Systems, Inc.
相關PDF資料 |
PDF描述 |
|---|---|
| LUCL9214AAJ-D | GT 19C 19#12 PIN RECP |
| LUCL9214AAJ-DT | Circular Connector; MIL SPEC:MIL-C-5015; Body Material:Metal; Series:GT; No. of Contacts:2; Connector Shell Size:24; Connecting Termination:Solder; Circular Shell Style:Square Flange Receptacle; Body Style:Straight |
| LUCL9214GAJ-D | Low-Cost Ringing SLIC |
| LUCL9214GAJ-DT | Low-Cost Ringing SLIC |
| LUCL9214GAU-D | Low-Cost Ringing SLIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LUCL9214AA-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
| LUCL9214AAJ-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
| LUCL9214AAJ-DT | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
| LUCL9214AAU-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
| LUCL9214ARG-D | 制造商:AGERE 制造商全稱:AGERE 功能描述:Low-Cost Ringing SLIC |
發布緊急采購，3分鐘左右您將得到回復。