- 您現在的位置：買賣IC網 > PDF目錄377803 > M25PE10-VMN6TG (意法半導體) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | M25PE10-VMN6TG |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 21/37頁 |
| 文件大?。?/td> | 198K |
| 代理商： | M25PE10-VMN6TG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
21/37
M25PE10, M25PE20
Sector Erase (SE)
The Sector Erase (SE) instruction sets to 1 (FFh)
all bits inside the chosen sector. Before it can be
accepted, a Write Enable (WREN) instruction
must previously have been executed. After the
Write Enable (WREN) instruction has been decod-
ed, the device sets the Write Enable Latch (WEL).
The Sector Erase (SE) instruction is entered by
driving Chip Select (S) Low, followed by the in-
struction code, and three address Bytes on Serial
Data Input (D). Any address inside the Sector (see
Table 3.
) is a valid address for the Sector Erase
(SE) instruction. Chip Select (S) must be driven
Low for the entire duration of the sequence.
The instruction sequence is shown in
Figure 17.
Chip Select (S) must be driven High after the
eighth bit of the last address Byte has been
latched in, otherwise the Sector Erase (SE) in-
struction is not executed. As soon as Chip Select
(S) is driven High, the self-timed Sector Erase cy-
cle (whose duration is t
SE
) is initiated. While the
Sector Erase cycle is in progress, the Status Reg-
ister may be read to check the value of the Write
In Progress (WIP) bit. The Write In Progress (WIP)
bit is 1 during the self-timed Sector Erase cycle,
and is 0 when it is completed. At some unspecified
time before the cycle is complete, the Write Enable
Latch (WEL) bit is reset.
A Sector Erase (SE) instruction applied to a sector
that contains a page that is Hardware Protected is
not executed.
Any Sector Erase (SE) instruction, while an Erase,
Program or Write cycle is in progress, is rejected
without having any effects on the cycle that is in
progress.
Figure 17. Sector Erase (SE)
Instruction Sequence
Note: Address bits A23 to A18 are Don’t Care in the M25PE20. Address bits A23 to A17 are Don’t Care in the M25PE10.
24 Bit Address
C
D
AI03751D
S
2
1
3
4
5
6
7
8
9
29 30 31
Instruction
0
23 22
2
0
1
MSB
相關PDF資料 |
PDF描述 |
|---|---|
| M25PE10-VMN6TP | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE20 | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE16 | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE16-VMP6G | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE16-VMP6P | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25PE10-VMN6TP | 功能描述:電可擦除可編程只讀存儲器 SERIAL PAGE ERASE FLASH 1 Mbit Datas RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M25PE10-VMN6TPBA | 制造商:Micron Technology Inc 功能描述:SERIAL NOR 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3V/3.3V 1Mbit 128K x 8bit 8ns T/R 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel |
| M25PE10-VMN6TPBA TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8SO |
| M25PE10-VMP6G | 制造商:Micron Technology Inc 功能描述:FLASH SERL-SPI 3.3V 1MBIT 128KX8 8NS 8PIN VDFPN EP - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8VFQFPN |
| M25PE10-VMP6P | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1 and 2 Mbit, page-erasable serial Flash memories with byte alterability, 75 MHz SPI bus, standard pinout |
發布緊急采購，3分鐘左右您將得到回復。