- 您現在的位置：買賣IC網 > PDF目錄358974 > M25PE80-VMP6 (意法半導體) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | M25PE80-VMP6 |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 25/43頁 |
| 文件大小： | 599K |
| 代理商： | M25PE80-VMP6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
25/43
M25PE80
Page Erase (PE)
The Page Erase (PE) instruction sets to 1 (FFh) all
bits inside the chosen page. Before it can be ac-
cepted, a Write Enable (WREN) instruction must
previously have been executed. After the Write
Enable (WREN) instruction has been decoded,
the device sets the Write Enable Latch (WEL).
The Page Erase (PE) instruction is entered by
driving Chip Select (S) Low, followed by the in-
struction code, and three address Bytes on Serial
Data Input (D). Any address inside the Page is a
valid address for the Page Erase (PE) instruction.
Chip Select (S) must be driven Low for the entire
duration of the sequence.
The instruction sequence is shown in
Figure 18.
.
Chip Select (S) must be driven High after the
eighth bit of the last address Byte has been
latched in, otherwise the Page Erase (PE) instruc-
tion is not executed. As soon as Chip Select (S) is
driven High, the self-timed Page Erase cycle
(whose duration is t
PE
) is initiated. While the Page
Erase cycle is in progress, the Status Register
may be read to check the value of the Write In
Progress (WIP) bit. The Write In Progress (WIP)
bit is 1 during the self-timed Page Erase cycle, and
is 0 when it is completed. At some unspecified
time before the cycle is complete, the Write Enable
Latch (WEL) bit is reset.
A Page Erase (PE) instruction applied to a page
that is Hardware or software Protected is not exe-
cuted.
Any Page Erase (PE) instruction, while an Erase,
Program or Write cycle is in progress, is rejected
without having any effects on the cycle that is in
progress.
Figure 18. Page Erase (PE)
Instruction Sequence
Note: Address bits A23 to A19 are Don’t Care.
24 Bit Address
C
D
AI04046
S
2
1
3
4
5
6
7
8
9
29 30 31
Instruction
0
23 22
2
0
1
MSB
相關PDF資料 |
PDF描述 |
|---|---|
| M25PE80-VMW6TG | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE80-VMW6TP | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE80-VMW6T | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE80-VMW6P | COIL CHOKE 27MH .50A RADIAL |
| M25PE80-VMW6G | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25PE80-VMP6G | 功能描述:閃存 8 Mbit Lo Vltg Page Erasable Seral 閃存 RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M25PE80-VMP6P | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:8-Mbit, page-erasable serial flash memory with byte alterability, 75 MHz SPI bus, standard pinout |
| M25PE80-VMP6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit, Low Voltage, Page-Erasable Serial Flash Memory with Byte-Alterability, 50MHz SPI Bus, Standard Pin-out |
| M25PE80-VMP6TG | 功能描述:閃存 SERIAL PAGE ERASE FLASH 8 Mbit Datas RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M25PE80-VMP6TP | 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:8-Mbit, page-erasable serial flash memory with byte alterability, 75 MHz SPI bus, standard pinout |
發布緊急采購，3分鐘左右您將得到回復。