- 您現在的位置：買賣IC網 > PDF目錄69008 > M30218MFCFP 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M30218MFCFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 123/161頁 |
| 文件大?。?/td> | 2043K |
| 代理商： | M30218MFCFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁當前第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁
Under
development
Tentative Specifications REV.A
Specifications in this manual are tentative and subject to change.
Mitsubishi microcomputers
M30218 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
64
FLD controller
Figure KA-11. FLDC Timing
Toff1
Tdisp
Toff1
Toff2
Tdisp
Grayscale display mode is not selected
(Address 035016 bit 5 = “0”)
Grayscale display mode is selected and set for bright display
(Address 035016 bit 5 = “1” and the corresponding grayscale
display control data = “0”)
Low output period for
blurring prevention
Display output period
Display output
period
Low output period for
blurring prevention
Grayscale display mode is selected and set for dark display
(Address 035016 bit 5 = “1” and the corresponding grayscale
display control data = “1”)
Low output period for
dark display
Timing setting
Each timing is set by the FLDC mode register, Tdisp time set register, Toff1 time set register, and Toff2 time set register.
Tdisp time setting
The Tdisp time represents the length of display timing. In non-gradation display mode, it consists of a
FLD display output period and a Toff1 time. In gradation display mode, it consists of the display output
period and Toff1 time plus a low signal output period for dark display. Set the Tdisp time by the Tdisp
counter count source select bit of the FLDC mode register and the Tdisp time set register. Supposing that
the value of the Tdisp time set register is n, the Tdisp time is represented as Tdisp = (n+1) x t (t: count
source). When the Tdisp counter count source select bit of the FLDC mode register is “0” and the value
of the Tdisp time set register is 200 (C816), the Tdisp time is: Tdisp = (200+1) x 3.2 (at XIN= 10 MHz) =
643
s. When reading the Tdisp time set register, the value in the counter is read out.
Toff1 time setting
The Toff1 time represents a non-output (low signal output) time to prevent blurring of FLD, and to dim the
display. Use the Toff1 time set register to set this Toff1 time. Make sure the value set to Toff1 is smaller
than Tdisp and Toff2. Supposing that the value of the Toff1 time set register is n1, the Toff1 time is
represented as Toff1 = n1 x t. When the Tdisp counter count source select bit of the FLDC mode register
is “0” and the value of the Toff1 time set register is 30 (1E16), Toff1 = 30 x 3.2 (at XIN = 10 MHz) = 96
s.
Toff2 time setting
The Toff2 time is provided for dark display. For bright display, the FLD display output remains effective
until the counter that is counting Tdisp reaches the terminal count. For dark display, however, “L” (or “off”)
signal is output when the counter that is counting Toff2 reaches the terminal count. This Toff2 time setting
is valid only for FLD ports which are in the gradation display mode and whose gradation display control
RAM value is “1” .
Set the Toff2 time by the Toff2 time set register. Make sure the value set to Toff2 is smaller than Tdisp but
larger than Toff1. Supposing that the value of the Toff2 time set register is n2, the Toff2 time is repre-
sented as Toff2 = n2 x t. When the Tdisp counter count source select bit of the FLDC mode register is “0”
and the value of the Toff2 time set register is 180 (B416), Toff2 = 180 x 3.2 (at XIN = 10 MHz) = 576
s.
相關PDF資料 |
PDF描述 |
|---|---|
| M30220FCRP | 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP144 |
| M30220MA-XXXGP | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP144 |
| M30220MA-XXXRP | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP144 |
| M30220FCRP | 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP144 |
| M30220FCGP | 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M3021E8F2-AXXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M3021E8F4-AXXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M3021E8F6-AXXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M3021E8F8-AXXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M3021E8FA-AXXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。