參數資料
型號: M30218MFCFP
元件分類: 微控制器/微處理器
英文描述: 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP100
封裝: PLASTIC, QFP-100
文件頁數: 66/161頁
文件大?。?/td> 2043K
代理商: M30218MFCFP
158
CPU Rewrite Mode
Under
development
Tentative Specifications REV.A
Specifications in this manual are tentative and subject to change.
Mitsubishi microcomputers
M30218 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Command
Program verify
Read
Program
03B616
First bus cycle
Second bus cycle
0016
4016
C016
Write
Program
address
Write
Read
Erase verify
A016
Write
Verify
address
Verify
data
Read
Erase
2016
Write
03B616
2016
Write
Verify
address
Reset
FF16
Write
Mode
Address
Mode
Address
Data
(D0 to D7)
Data
(D0 to D7)
03B616
Program
data
Verify
data
FF16
Write
03B616
Software Commands
Table BB-1 lists the software commands available with the M30218 group (flash memory version).
When CPU rewrite mode is enabled, write software commands to the flash command register to specify
the operation to erase or program.
The content of each software command is explained below.
Table BB-1. List of Software Commands (CPU Rewrite Mode)
Read Command (0016)
The read mode is entered by writing the command code “0016” to the flash command register in the
first bus cycle. When an address to be read is input in one of the bus cycles that follow, the content of
the specified address is read out at the data bus (D0–D7), 8 bits at a time.
The read mode is retained intact until another command is written.
After reset and after the reset command is executed, the read mode is set.
Program Command (4016)
The program mode is entered by writing the command code “4016” to the flash command register in
the first bus cycle. When the user execute an instruction to write byte data to the desired address (e.g.,
STE instruction) in the second bus cycle, the flash memory control circuit executes the program op-
eration. The program operation requires approximately 20
s. Wait for 20 s or more before the user
go to the next processing.
During program operation, the watchdog timer remains idle, with the value “7FFF16” set in it.
Note 1: The write operation is not completed immediately by writing a program command once. The
user must always execute a program-verify command after each program command executed. And if
verification fails, the user need to execute the program command repeatedly until the verification
passes. See Figure BB.3 for an example of a programming flowchart.
相關PDF資料
PDF描述
M30220FCRP 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP144
M30220MA-XXXGP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP144
M30220MA-XXXRP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP144
M30220FCRP 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP144
M30220FCGP 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP144
相關代理商/技術參數
參數描述
M3021E8F2-AXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M3021E8F4-AXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M3021E8F6-AXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M3021E8F8-AXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M3021E8FA-AXXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER