- 您現在的位置：買賣IC網 > PDF目錄45019 > M30624MGM-XXXGP 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100 PDF資料下載
參數資料
| 型號： | M30624MGM-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100 |
| 封裝： | PLASTIC, QFP-100 |
| 文件頁數： | 21/30頁 |
| 文件大?。?/td> | 379K |
| 代理商： | M30624MGM-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
Rev.3.01
2005.02.07
page 28 of 111
REJ03B0106-0301
4506 Group
Fig. 23 Count timing diagram at CNTR input
(8) Timer input/output pin (P12/CNTR pin)
CNTR pin is used to input the timer 2 count source and output the
timer 1 and timer 2 underflow signal divided by 2.
The P12/CNTR pin function can be selected by bit 0 of register
W6. The CNTR output signal can be selected by bit 1 of register
W6.
When the CNTR input is selected for timer 2 count source, timer 2
counts the falling waveform of CNTR input.
(9) Precautions
Note the following for the use of timers.
Prescaler
Stop the prescaler operation to change its frequency dividing ratio.
Count source
Stop timer 1 or 2 counting to change its count source.
Reading the count value
Stop timer 1 or 2 counting and then execute the TAB1 or TAB2 in-
struction to read its data.
Writing to the timer
Stop timer 1 or 2 counting and then execute the T1AB or T2AB in-
struction to write its data.
Writing to reload register R1
When writing data to reload register R1 while timer 1 is operating,
avoid a timing when timer 1 underflows.
0316
0216
0116
0016
FF16
FE16
CNTR input
Timer 2 count
Timer 2 interrupt
request flag
(T2F)
(Note)
Note: This is an example when “FF16” is set to timer 2 reload register R2L.
Timer 1 and timer 2 count start timing and count time when op-
eration starts
Count starts from the first rising edge of the count source (2) af-
ter timer 1 and timer 2 operations start (1).
Time to first underflow (3) is shorter (for up to 1 period of the
count source) than time among next underflow (4) by the timing
to start the timer and count source operations after count starts.
When selecting CNTR input as the count source of timer 2, timer
2 operates synchronizing with the falling edge of CNTR input.
Fig. 24 Timer count start timing and count time when opera-
tion starts (T1, T2)
(1) Timer
Count Source
Timer Value
Timer Underflow
Signal
3
21
032
103
2
Count Source
(CNTR input)
(2)
(3)
(4)
相關PDF資料 |
PDF描述 |
|---|---|
| M30624FGMFP | 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP100 |
| M30624MGM-XXXGP | 16-BIT, MROM, 10 MHz, MICROCONTROLLER, PQFP100 |
| M30624FGAGP#U3 | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
| M30620FCMGP | 16-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP100 |
| M30620FCAFP | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30624MGN-XXXFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30624MGN-XXXGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30624MGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30624MGP-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30624MGP-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。