參數資料
型號： M30845FJGP
元件分類： 微控制器/微處理器
英文描述： 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP144
封裝： 20 X 20 MM, 0.50 MM PITCH, PLASTIC, LQFP-144
文件頁數： 54/91頁
文件大小： 903K
代理商： M30845FJGP
57
38C2 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e parametric
limits
are
subject
to
change.
Fig. 61 Block diagram of built-in flash memory
(1) CPU Rewrite Mode
In CPU rewrite mode, the internal flash memory can be operated
on (read, program, or erase) under control of the Central Process-
ing Unit (CPU).
In CPU rewrite mode, only the User ROM area shown in Figure 61
can be rewritten; the Boot ROM area cannot be rewritten. Make
sure the program and block erase commands are issued for only
the User ROM area and each block area.
The control program for CPU rewrite mode can be stored in either
User ROM or Boot ROM area. In the CPU rewrite mode, because
the flash memory cannot be read from the CPU, the rewrite con-
trol program must be transferred to internal RAM area before it
can be executed.
Boot Mode
The control program for CPU rewrite mode must be written into
the User ROM or Boot ROM area in parallel I/O mode beforehand.
(If the control program is written into the Boot ROM area, the stan-
dard serial I/O mode becomes unusable.)
See Figure 61 for details about the Boot ROM area.
Normal microcomputer mode is entered when the microcomputer
is reset with pulling CNVSS pin low. In this case, the CPU starts
operating using the control program in the User ROM area.
When the microcomputer is reset by pulling the P41(CE) pin high,
the CNVSS pin high, the CPU starts operating (start address of
program is stored into addresses FFFC16 and FFFD16) using the
control program in the Boot ROM area. This mode is called the
“Boot mode”. Also, User ROM area can be rewritten using the con-
trol program in the Boot ROM area.
Block Address
Block addresses refer to the maximum address of each block.
These addresses are used in the block erase command.
100016
800016
FFFF16
F00016
FFFF16
M38C29FF
100016
100016
800016
FFFF16
F00016
FFFF16
BSEL=0BSEL=1
User ROM area
4 Kbytes
Boot ROM area
Notes 1: The Boot ROM area can be rewritten in only parallel I/O mode.
(Access to any other areas is inhibited.)
2: To specify a block, use the maximum address in the block.
Parallel I/O mode
CPU rewrite mode, standard serial I/O mode
User area / Boot area select bit = “0”
Block 1 : 28 Kbytes
User ROM area
4 Kbytes
Boot ROM area
Block 1 : 28 Kbytes
Block 0 : 32 Kbytes
User area / Boot area select bit = “1”
Product name
Flash memory
top address
相關PDF資料
PDF描述
M30843FHGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100
M30845FHGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP144
M30843FWTGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100
M30842MC-XXXGP 32-BIT, MROM, 32 MHz, MICROCONTROLLER, PQFP144
M30843FJGP 32-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP100
相關代理商/技術參數
參數描述
M30845FJGP D3 制造商:Renesas Electronics Corporation 功能描述:
M30845FJGP D5 制造商:Renesas Electronics Corporation 功能描述:
M30845FJGP#U3 功能描述:IC M32C MCU FLASH 512K 144LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M32C/80/84 標準包裝:160 系列:S08 核心處理器:S08 芯體尺寸:8-位 速度:40MHz 連通性:I²C，LIN，SCI，SPI 外圍設備:LCD，LVD，POR，PWM，WDT 輸入/輸出數:53 程序存儲器容量:32KB（32K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1.9K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 12x12b 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:64-LQFP 包裝:托盤
M30845FJGP#U5 功能描述:IC M32C MCU FLASH 512K 144LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:M16C™ M32C/80/84 標準包裝:96 系列:PIC® 16F 核心處理器:PIC 芯體尺寸:8-位 速度:20MHz 連通性:I²C，SPI 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:11 程序存儲器容量:3.5KB（2K x 14） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:128 x 8 電壓 - 電源 (Vcc/Vdd):2.3 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:14-TSSOP（0.173"，4.40mm 寬） 包裝:管件
M30845FJTGP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 16/32-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*