- 您現在的位置：買賣IC網 > PDF目錄359054 > M30L0R8000T0ZAQF (意法半導體) 256 Mbit (16Mb x16, Multiple Bank, Multi-Level, Burst) 1.8V Supply Flash Memory PDF資料下載
參數資料
| 型號： | M30L0R8000T0ZAQF |
| 廠商： | 意法半導體 |
| 英文描述： | 256 Mbit (16Mb x16, Multiple Bank, Multi-Level, Burst) 1.8V Supply Flash Memory |
| 中文描述： | 256兆位（16Mb的x16插槽，多銀行，多層次，多突發）1.8V電源快閃記憶體 |
| 文件頁數： | 24/83頁 |
| 文件大?。?/td> | 1363K |
| 代理商： | M30L0R8000T0ZAQF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁
M30L0R8000T0, M30L0R8000B0
24/83
STATUS REGISTER
The Status Register provides information on the
current or previous program or erase operations.
Issue a Read Status Register command to read
the contents of the Status Register, refer to Read
Status Register Command section for more de-
tails. To output the contents, the Status Register is
latched and updated on the falling edge of the
Chip Enable or Output Enable signals and can be
read until Chip Enable or Output Enable returns to
V
IH
. The Status Register can only be read using
single Asynchronous or Single Synchronous
reads. Bus Read operations from any address
within the bank, always read the Status Register
during program and erase operations.
The various bits convey information about the sta-
tus and any errors of the operation. Bits SR7, SR6,
SR2 and SR0 give information on the status of the
device and are set and reset by the device. Bits
SR5, SR4, SR3 and SR1 give information on er-
rors, they are set by the device but must be reset
by issuing a Clear Status Register command or a
hardware reset. If an error bit is set to ‘1’ the Status
Register should be reset before issuing another
command.
The bits in the Status Register are summarized in
Table 9., Status Register Bits
. Refer to
Table 9.
in
conjunction with the following text descriptions.
Program/Erase Controller Status Bit (SR7).
The
Program/Erase Controller Status bit indicates
whether the Program/Erase Controller is active or
inactive in any bank.
When the Program/Erase Controller Status bit is
Low (set to ‘0’), the Program/Erase Controller is
active; when the bit is High (set to ‘1’), the Pro-
gram/Erase Controller is inactive, and the device
is ready to process a new command.
The Program/Erase Controller Status bit is Low
immediately after a Program/Erase Suspend com-
mand is issued until the Program/Erase Controller
pauses. After the Program/Erase Controller paus-
es the bit is High.
Erase Suspend Status Bit (SR6).
The
Suspend Status bit indicates that an erase opera-
tion has been suspended in the addressed block.
When the Erase Suspend Status bit is High (set to
‘1’), a Program/Erase Suspend command has
been issued and the memory is waiting for a Pro-
gram/Erase Resume command.
The Erase Suspend Status bit should only be con-
sidered valid when the Program/Erase Controller
Status bit is High (Program/Erase Controller inac-
tive). SR6 is set within the Erase Suspend Latency
time of the Program/Erase Suspend command be-
ing issued therefore the memory may still com-
Erase
plete the operation rather than entering the
Suspend mode.
When a Program/Erase Resume command is is-
sued the Erase Suspend Status bit returns Low.
Erase Status Bit (SR5).
The Erase Status bit is
used to identify if there was an error during a block
or bank erase operation. When the Erase Status
bit is High (set to ‘1’), the Program/Erase Control-
ler has applied the maximum number of pulses to
the block or bank and still failed to verify that it has
erased correctly.
The Erase Status bit should be read once the Pro-
gram/Erase Controller Status bit is High (Program/
Erase Controller inactive).
Once set High, the Erase Status bit must be set
Low by a Clear Status Register command or a
hardware reset before a new erase command is is-
sued, otherwise the new command will appear to
fail.
Program Status Bit (SR4).
The Program Status
bit is used to identify if there was an error during a
program operation.
The Program Status bit should be read once the
Program/Erase Controller Status bit is High (Pro-
gram/Erase Controller inactive).
When the Program Status bit is High (set to ‘1’),
the Program/Erase Controller has applied the
maximum number of pulses to the Word and still
failed to verify that it has programmed correctly.
Attempting to program a '1' to an already pro-
grammed bit while V
PP
= V
PPH
will also set the
Program Status bit High. If V
PP
is different from
V
PPH
, SR4 remains Low (set to '0') and the attempt
is not shown.
Once set High, the Program Status bit must be set
Low by a Clear Status Register command or a
hardware reset before a new program command is
issued, otherwise the new command will appear to
fail.
V
PP
Status Bit (SR3).
The V
PP
Status bit is used
to identify an invalid voltage on the V
PP
pin during
program and erase operations. The V
PP
pin is only
sampled at the beginning of a program or erase
operation. Program and erase operations are not
guaranteed if V
PP
becomes invalid during an oper-
ation.
When the V
PP
Status bit is Low (set to ‘0’), the volt-
age on the V
PP
pin was sampled at a valid voltage.
when the V
PP
Status bit is High (set to ‘1’), the V
PP
pin has a voltage that is below the V
PP
Lockout
Voltage, V
PPLK
, the memory is protected and pro-
gram and erase operations cannot be performed.
相關PDF資料 |
PDF描述 |
|---|---|
| M30L0R8000T0ZAQT | 256 Mbit (16Mb x16, Multiple Bank, Multi-Level, Burst) 1.8V Supply Flash Memory |
| M30L0R8000T0ZAQE | AB 35C 7#12,28#16 PIN RECP |
| M30L0R8000B0ZAQE | 256 Mbit (16Mb x16, Multiple Bank, Multi-Level, Burst) 1.8V Supply Flash Memory |
| M30L0R8000B0ZAQF | CAP 0.1UF 50V 10% X7R DIP-2 BULK S-MIL-C-39014 |
| M30L0R8000B0ZAQT | 256 Mbit (16Mb x16, Multiple Bank, Multi-Level, Burst) 1.8V Supply Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M30L0R8000T0ZAQT | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Mbit (16Mb x16, Multiple Bank, Multi-Level, Burst) 1.8V Supply Flash Memory |
| M30L40C | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Dual Common-Cathode Schottky Rectifier |
| M30L40C-E3/4W | 功能描述:肖特基二極管與整流器 40 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel |
| M30L45C-E3/4W | 功能描述:肖特基二極管與整流器 45 Volt 30 Amp Dual Common-Cathode RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel |
| M30LLASSM | 制造商:Apex Tool Group 功能描述:Syringe; Manual Assemble Calibrated Syringe; 30 cc 制造商:Cooper Hand Tools / Weller 功能描述:CALIBRATED SYRINGE, 30CC; Dispenser Type:Syringe; Volume:30cc; Accessory Type:Calibrated Syringe |
發布緊急采購，3分鐘左右您將得到回復。