Rev.1.00
2003.11.25
page 91 of 128
M37161M8/MA/MF-XXXSP/FP,M37161EFSP/FP
Max.
30
45
200
2
100
10
0.4
3.0
0.4
0.6
1.3
5
130
VCC = 5.5V,
f(XIN) = 8MHz
VCC = 5.5V, f(XIN) = 0,
f(XCIN) = 32kHz,
OSD OFF
Low-power dissipation mode set
(CM5 = “0”, CM6 = “1”)
VCC = 5.5 V, f(XIN) = 8 MHz
VCC = 5.5 V, f(XIN) = 0,
f(XCIN) = 32 kHz,
Low-power dissipation mode set
(CM5 = “0”, CM6 = “1”)
VCC = 5.5V, f(XIN) = 0,
f(XCIN) = 0
VCC = 4.5 V
IOH = –0.5 mA
VCC = 4.5 V
IOL = 0.5 mA
VCC = 4.5 V
IOL = 10.0 mA
VCC = 4.5 V
VCC = 5.0 V
VCC = 5.5 V
VI = 5.5 V
VCC = 5.5 V
VI = 0 V
VCC = 4.5 V
12. ELECTRIC CHARACTERISTICS (VCC = 5 V ± 10 %, VSS = 0 V, f(XIN) = 8 MHz, Ta = –10 °C to 70 °C, unless otherwise noted)
Notes 1: The total current that flows out of the IC must be 20 mA or less.
2: The total input current to IC (IOL1 + IOL2) must be 30 mA or less.
3: The total average input current for ports P24–P27 and AVCC–VSS to IC must be 20 mA or less.
4: Connect 0.1
F or more capacitor externally between the power source pins VCC–VSS so as to reduce power source noise.
Also connect 0.1
F or more capacitor externally between the pins VCC–CNVSS.
5: Use a quartz-crystal oscillator or a ceramic resonator for the CPU oscillation circuit(XIN,XOUT).
6: P06, P07, P16, P23, P24, P25 have hysteresis when used as interrupt input pins or timer input pins. P11–P14, P30, P31 have hysteresis when used as multi-
master I2C-BUS interface ports. P20–P22 have hysteresis when used as serial I/O pins.
7: Pin names in each parameter are described as below.
(1) Dedicated pins: dedicated pin names.
(2) Double-/triple-function ports
Same limits: I/O port name.
Functions other than ports vary from I/O port limits : function pin name.
HIGH output voltage
P10–P16, P20–P27,
P30, P31, P52–P55,
LOW output voltage
P00–P07, P10,
P15, P16, P20–P23,
P52–P55
LOW output voltage
P24– P27
LOW output voltage
P11–P14, P30, P32
Hysteresis (See note 6)
____________
RESET, P50, P51, INT1, INT2,
INT3, TIM2, TIM3, SIN, SCLK, SCL1,
SCL2, SCL3, SDA1, SDA2, SDA3
HIGH input leak current
P00–P07, P10–P16, P20–P27,
____________
P30, P31,P35–P37, RESET, P50, P51,
LOW input leak current
P00–P07, P10–P16, P20–P27, P30, P31,
____________
P35–P37, P50, P51, RESET
I2C-BUS BUS switch connection resistor
(between SCL1 and SCL2, SDA1 and SDA2)
ICC
Symbol
Parametear
Test conditions
OSD OFF
OSD ON
Stop mode
Wait mode
System operation
Power source current
VOH
VOL
VT+ –VT–
IIZH
IIZL
RBS
Test
circuit
1
Min.
2.4
Limits
IOL = 3 mA
IOL = 6 mA
Typ.
15
30
60
1
25
1
0.5
2
3
4
5
4
Unit
mA
A
mA
A
V
A