參數資料
型號： M37161EFSP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP42
封裝： 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-42
文件頁數： 56/129頁
文件大?。?/td> 1092K
代理商： M37161EFSP
Rev.1.00
2003.11.25
page 32 of 128
M37161M8/MA/MF-XXXSP/FP,M37161EFSP/FP
8.6.3 I2C Clock Control Register
The I2C clock control register (address 00FA16) is used to set ACK
control, SCL mode and SCL frequency.
(1) Bits 0 to 4: SCL frequency control bits (CCR0–CCR4)
These bits control the SCL frequency.
(2) Bit 5: SCL mode specification bit (FAST MODE)
This bit specifies the SCL mode. When this bit is set to “0,” the stan-
dard clock mode is set. When the bit is set to “1,” the high-speed
clock mode is set.
(3) Bit 6: ACK bit (ACK BIT)
This bit sets the SDA status when an ACK clock is generated. When
this bit is set to “0,” the ACK return mode is set and SDA goes to
LOW at the occurrence of an ACK clock. When the bit is set to “1,”
the ACK non-return mode is set. The SDA is held in the HIGH status
at the occurrence of an ACK clock.
Fig. 8.6.4 I2C Clock Control Register
However, when the slave address matches the address data in the
reception of address data at ACK BIT = “0,” the SDA is automatically
goes to LOW (ACK is returned). If there is a mismatch between the
slave address and the address data, the SDA is automatically goes
to HIGH (ACK is not returned).
ACK clock: Clock for acknowledgement
(4) Bit 7: ACK clock bit (ACK)
This bit specifies a mode of acknowledgment which is an acknowl-
edgment response of data transmission. When this bit is set to “0,”
the no ACK clock mode is set. In this case, no ACK clock occurs
after data transmission. When the bit is set to “1,” the ACK clock
mode is set and the master generates an ACK clock upon comple-
tion of each 1-byte data transmission.The device for transmitting
address data and control data releases the SDA at the occurrence of
an ACK clock (make SDA HIGH) and receives the ACK bit generated
by the data receiving device.
Note: Do not write data into the I2C clock control register during transmission.
If data is written during transmission, the I2C clock generator is reset, so
that data cannot be transmitted normally.
b7 b6 b5 b4 b3 b2 b1 b0
I2C clock control register (S2) [Address 00FA16]
I2C Clock Control Register
0
to
4
SCL frequency control
bits
(CCR0 to CCR4)
7
5
6
SCL mode
specification bit
(FAST MODE)
0: Standard clock mode
1: High-speed clock mode
0
Standard
clock
mode
Functions
Name
After reset
RW
B
0
ACK bit
(ACK BIT)
ACK clock bit
(ACK)
0: ACK is returned.
1: ACK is not returned.
0: No ACK clock
1: ACK clock
High speed
clock mode
Setup disabled
00 to 02
Setup disabled
333
03
Setup disabled
250
04
100
400 (See note)
05
83.3
166
06
500/CCR value 1000/CCR value
...
17.2
34.5
1D
16.6
33.3
1E
16.1
32.3
1F
(
φ = at 4 MHz, unit : kHz)
Notes 1. At 400kHz in the high-speed clock mode, the duty is as below .
“0” period : “1” period = 3 : 2
In the other cases, the duty is as below.
“0” period : “1” period = 1 : 1
Setup value
of CCR4–
CCR0
RW
相關PDF資料
PDF描述
M37161MA-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
M37161M8-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
M37202E3SP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP64
M37207EFFP 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PQFP80
M37207MF-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP64
相關代理商/技術參數
參數描述
M37161M8 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37161M8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37161M8-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37161MA-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37161MA-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*