參數資料
型號: M37161EFSP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PDIP42
封裝: 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-42
文件頁數: 60/129頁
文件大?。?/td> 1092K
代理商: M37161EFSP
Rev.1.00
2003.11.25
page 36 of 128
M37161M8/MA/MF-XXXSP/FP,M37161EFSP/FP
(8) Bit 7: Communication mode specification bit
(master/slave specification bit: MST)
This bit is used for master/slave specification in data communica-
tions. When this bit is “0,” the slave is specified, so that a START
condition and a STOP condition generated by the master are received,
and data communication is performed in synchronization with the
clock generated by the master. When this bit is “1,” the master is
specified and a START condition and a STOP condition are gener-
ated, and also the clocks required for data communication are gen-
erated on the SCL.
Fig. 8.6.8 I2C Status Register
b7
b3 b2 b1 b0
I2C status register (S1) [Address 00F816]
I
2
r
0
3
4
5
6, 7
b7 b6
0
0 : Slave recieve mode
0
1 : Slave transmit mode
1
0 : Master recieve mode
1
1 : Master transmit mode
1
2
0
1
0
B
Name
Functions
After reset
Communication mode
specification bits
(TRX, MST)
0 : Bus free
1 : Bus busy
Bus busy flag (BB)
0 : Interrupt request issued
1 : No interrupt request issued
I2C-BUS interface interrupt
request bit (PIN)
0 : Not detected
1 : Detected
Arbitration lost detecting flag
(AL) (See note)
0 : Address mismatch
1 : Address match
Slave address comparison
flag (AAS) (See note)
0 : No general call detected
1 : General call detected
General call detecting flag
(AD0) (See note)
0 : Last bit = “0 ”
1 : Last bit = “1 ”
Last receive bit (LRB)
(See note)
Note : These bits and flags can be read out, but cannnot be written.
Indeterminate
0
W
R
R —
RW
(See note)
Fig. 8.6.9 Interrupt Request Signal Generation Timing
SCL
PIN
IICIRQ
The MST bit is cleared to “0” in any of the following conditions.
Immediately after completion of 1-byte data transmission when
arbitration lost is detected
When a STOP condition is detected.
When occurence of a START condition is disabled by the START
condition duplication prevention function (Note).
At reset
Note: The START condition duplication prevention function disables the START
condition generation, bit counter reset, and SCL output, when the follow-
ing condition is satisfied:
a START condition is set by another master device.
相關PDF資料
PDF描述
M37161MA-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
M37161M8-XXXSP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP42
M37202E3SP 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP64
M37207EFFP 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PQFP80
M37207MF-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP64
相關代理商/技術參數
參數描述
M37161M8 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37161M8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37161M8-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37161MA-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37161MA-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER