- 您現在的位置：買賣IC網 > PDF目錄45035 > M37546G4-XXXHP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 PDF資料下載
參數資料
| 型號： | M37546G4-XXXHP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 |
| 封裝： | 6 X 6 MM, 0.50 MM PITCH, PLASTIC, WQFN-36 |
| 文件頁數： | 31/103頁 |
| 文件大?。?/td> | 1156K |
| 代理商： | M37546G4-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁
REJ03B0160-0122 Rev.1.22 Mar 13, 2009
page 33 of 100
7546 Group
Output compare
7546 group has 4-output compare channels. Each channel (0 to 3)
has the same function and can be used to output waveform by us-
ing count value of either Timer A or Timer B.
The source timer for each channel is selected by setting value of
the compare x (x = 0, 1, 2, 3) timer source bit. Timer A and Timer B
can be selected for the source timer to each channel, respectively.
To use each compare channel, set “1” to the compare x output
port bit and set the port direction register corresponding to com-
pare channel to output mode.
The compare value for each channel is set to the compare regis-
ter (low-order) and compare register (high-order).
Writing to the register for each channel is controlled by setting
value of compare register write pointer. Writing to each register is
in the following order;
1.Set the value of corresponded output compare channel to the
compare register write pointer.
2.Write a value to the compare register (low-order) and compare
register (high-order).
3.Set “1” to the compare latch y (y = 00, 01, 10, 11, 20, 21, 30, 31)
re-load bit.
When “1” is set to the compare latch y re-load bit, the value set
to the compare register is loaded to compare latch when the
next timer underflow.
When count value of timer and setting value of compare latch is
matched, compare output trigger occurs.
When “1: Enabled” is set to the compare trigger x enable bit, the
output waveform from port is inverted by compare trigger.
When “0: Disabled” is set to the compare trigger x enable bit, the out-
put waveform is not inverted, so port output can be fixed to “H” or “L”.
When “0: Positive” is set to the compare x output level latch, the
compare output waveform is turned to “H level” at compare latch
x0’s match and turned to “L level” at compare latch x1’s match.
When “1 :Negative” is set to the compare x output level latch, the
compare output waveform is turned to “L level” at compare latch
x0’s match and turned to “H level” at compare latch x1’s match.
The compare output level of each channel can be confirmed by
reading the compare x output status bit.
Compare output interrupt is available when match of each com-
pare channel and timer count value. The interrupt request from
each channel can be disabled or enabled by setting value of com-
pare latch y interrupt source bit.
Compare 0,1 (2,3) modulation mode
In compare modulation mode, modulation waveform can be gener-
ated by using compare channel 0 and 1, or compare channel 2 and 3.
To use this mode,
Set “1: Enabled” to the compare 0,1 (2, 3) modulation mode bit.
Set Timer A underflow for Timer B count source.
Set Timer A for the timer source of compare channel 0 (2).
Set Timer B for the timer source of compare channel 1 (3).
In this mode, AND waveform of compare 0 (1) and compare 2 (3)
is generated from Port P01 and P31, respectively. Accordingly, in
order to use this mode, set “1” to the compare 0 output port bit or
compare 2 output port bit.
Fig. 32 Structure of capture/compare register R/W pointer
Fig. 33 Structure of compare register re-load register
b7
b0
Compare register R/W pointer
b2 b1 b0
000 : Compare latch 00
001 : Compare latch 01
010 : Compare latch 10
011 : Compare latch 11
100 : Compare latch 20
101 : Compare latch 21
110 : Compare latch 30
111 : Compare latch 31
Not used (returns “0” when read)
Capture register 0 R/W pointer
0: Capture latch 00
1: Capture latch 01
Capture register 1 R/W pointer
0: Capture latch 10
1: Capture latch 11
Not used (returns “0” when read)
Capture/compare register R/W pointer
(CCRP : address 001216, initial value: 0016)
b7
b0
Compare latch 00, 01 re-load bit
0: Re-load disabled
1: Re-load at next underflow
Compare latch 10, 11 re-load bit
0: Re-load disabled
1: Re-load at next underflow
Compare latch 20, 21 re-load bit
0: Re-load disabled
1: Re-load at next underflow
Compare latch 30, 31 re-load bit
0: Re-load disabled
1: Re-load at next underflow
Not used (returns “0” when read)
Compare register re-load register
(CMPR : address 001416, initial value: 0016)
■ Notes on Output Compare
When the selected source timer of each compare channel is
stopped, written data to compare register is loaded to the com-
pare latch simultaneously.
Do not write the same data to both of compare latch x0 and x1.
When setting value of the compare latch is larger than timer set-
ting value, compare match signal is not generated. Accordingly,
the output waveform is fixed to “L” or “H” level.
However, when setting value of another compare latch is
smaller than timer setting value, this compare match signal is
generated. Accordingly, compare match interrupt occurs.
When the compare x trigger enable bit is cleared to “0” (dis-
abled), the match trigger to the waveform output circuit is
disabled, and the output waveform can be fixed to “L” or “H”
level.
However, in this case, the compare match signal is generated.
Accordingly, compare match interrupt occurs.
相關PDF資料 |
PDF描述 |
|---|---|
| M37546G2GP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37546G2HP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 |
| M37546G4-XXXSP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP32 |
| M37546G4-XXXGP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37547G2-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37546G4-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37547G2FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37547G2FP#U0 | 功能描述:MCU 2/5V 8KB 36-SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 標準包裝:250 系列:80C 核心處理器:8051 芯體尺寸:8-位 速度:16MHz 連通性:EBI/EMI，I²C，UART/USART 外圍設備:POR，PWM，WDT 輸入/輸出數:40 程序存儲器容量:- 程序存儲器類型:ROMless EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-LCC（J 形引線） 包裝:帶卷 (TR) |
| M37547G2-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37547G4FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。