參數資料
型號： M37641F8FP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 143/149頁
文件大?。?/td> 1997K
代理商： M37641F8FP
143
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
change.
Some parametric limits are subject to
USB
When the USB Reset Interrupt Status Flag is kept at “1”, all other
flags in the USB internal registers (addresses 0050
16
to 005E
16
)
will return to their reset status. However, the following registers
are not affected by the USB reset: USB control register (address
0013
16
), Frequency synthesizer control register (address
006C
16
), Clock control register (address 001F
16
), and USB end-
point-x FIFO register (addresses 0060
16
to 0064
16
).
When not using the USB function, set the USB Line Driver Supply
Enable Bit of the USB control register (address 0013
16
) to “1” for
power supply to the internal circuits (at Vcc = 5V).
When using an isochronous transfer, set the FLUSH Bit (bit 6 of
address 0059
16
and bit 6 of address 005A
16
) as follows:
IN FIFO: use AUTO_FLUSH Bit (bit 6 of 0058
16
)
OUT FIFO: when OUT_PKT_RDY Bit is “1”, set FLUSH Bit to “1”
When the USB SOF Port Select Bit is “1”, the reference pulse of
83.3 ns (
φ
= 12 MHz) is output from the P7
0
/SOF pin and syn-
chronized with the SOF packet.
The receive buffer full interrupt request is not generated if receive
errors are detected at receiving.
If a character bit length is 7 bits, bit 7 of the UARTx transmit/re-
ceive buffer register 1 and bits 0 to 7 of the UARTx transmit/
receive buffer register 2 are ignored at transmitting; they are in-
valid at receiving.
If a character bit length is 8 bits, bits 0 to 7 of the UARTx transmit/
receive buffer register 2 are ignored at transmitting; they are in-
valid at receiving.
If a character bit length is 9 bits, bits 1 to 7 of the UARTx transmit/
receive buffer register 2 are ignored at transmitting; they are “0”
at receiving.
The IN_PKT_RDY Bit and OUT_PKT_RDY Flag can be set or
cleared by software even when using the AUTO_SET or
AUTO_CLR function.
When writing to USB-related registers, set the USB Clock Enable
Bit to “1”, then perform the write after four
φ
cycle waits.
When using the MCU at Vcc = 3.3V, set the USB Line Driver Sup-
ply Enable Bit to “0” (line driver disable). Note that setting the
USB Line Driver Current Control Bit (USBC3) doesn’t affect the
USB operation.
Read one packet data from the OUT FIFO before clearing the
OUT_PKT_RDY Flag. If the OUT_PKT_RDY Flag is cleared
while one packet data is being read, the internal read pointer can-
not operate normally.
Use the transfer instructions such as
LDA
and
STA
to set the reg-
isters: USB interrupt status registers 1, 2 (addresses 0052
16
,
0053
16
); USB endpoint 0 IN control register (address 0059
16
);
USB endpoint x IN control register (address 0059
16
); USB end-
point x OUT control register (address 005A
16
). Do not use the
read-modify-write instructions such as the
SEB
or the
CLB
in-
struction.
When writing to bits shown by Table 39 using the transfer instruc-
tion such as
LDA
or
STA
, a value which never affect its bit state
is required. Take the following sequence to change these bits
contents:
(1) Store the register contents onto a variable or a data register.
(2) Change the target bit on the variable or the data register. Si-
multaneously mask the bit so that its bit state cannot be
changed. (See to Table 39.)
(3) Write the value from the variable or the data register to the
register using the transfer instruction such as
LDA
or
STA.
Table 39 Bits of which state might be changed owing to software write
Regster name
USB endpoint 0 IN control register
USB endpoint x (x = 1 to 4) IN control register
USB endpoint x (x = 1 to 4) OUT control register
Bit name
IN_PKT_RDY (b1)
DATA_END (b3)
FORCE_STALL (b4)
IN_PKT_RDY (b0)
UNDER_RUN (b1)
OUT_PKT_RDY (b0)
OVER_RUN (b1)
FORCE_STALL (b4)
DATA_ERR (b5)
Value not affecting state (
Note
)
“0”
“0”
“1”
“0”
“1”
“1”
“1”
“1”
“1”
Note:
Writing this value will not change the bit state, because this value cannot be written to the bit by software.
相關PDF資料
PDF描述
M37641F8HP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641M8-100FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641M8-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37702M2-127FP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37702S1AFP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
相關代理商/技術參數
參數描述
M37641F8FP#U0 功能描述:IC 740 MCU FLASH 32K 80QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/7600 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
M37641F8HP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8HP#U0 功能描述:IC 740 MCU FLASH 32K 80LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/7600 產品培訓模塊:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 標準包裝:27 系列:PIC® 24H 核心處理器:PIC 芯體尺寸:16-位 速度:40 MIP 連通性:I²C，SPI，UART/USART 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:21 程序存儲器容量:12KB（4K x 24） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 3.6 V 數據轉換器:A/D 10x10b/12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 包裝:管件 產品目錄頁面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
M37641F8M8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*