參數資料
型號： M37641F8FP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 53/149頁
文件大?。?/td> 1997K
代理商： M37641F8FP
53
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
change.
Some parametric limits are subject to
[USB Endpoint 0 IN Control Register ] IN_CSR
This register contains the control and status information of the
endpoint 0. This USB FCU sets the OUT_PKT_RDY flag to
“
1
”
upon having received a data packet in the OUT FIFO. When read-
ing its one data packet from the OUT FIFO, be sure to set this flag
to
“
0
”
.
After a SETUP token is received, the MCU is in the
“
decode wait
state
”
until the OUT_PKT_RDY flag is cleared. If the
OUT_PKT_RDY flag is not cleared (indicating that the host re-
quest has not been successfully decoded), the USB FCU keep
returning a NAK to the host for all IN/OUT tokens.
Set the IN_PKT_RDY bit to
“
1
”
after the data packet has been
written to the IN FIFO. If this bit is set to
“
1
”
even though nothing
has been written to the IN FIFO, a
“
0
”
length data (NULL packet)
is sent to the host. The SEND_STALL bit is for sending a STALL to
the host if an unsupported request is received by the USB FCU.
This bit must be set to
“
1
”
(which instructs the FCU USB to send a
STALL signal) whenever an unsupported device request is re-
ceived from the host. The setup process is as follows:
(1) Set SEND_STALL bit to
“
1
”
(2) Set DATA_END bit to
“
1
”
(3) Set OUT_PKT_RDY flag to
“
0
”
.
Note that if
“
0
”
is written to the SEND_STALL bit before the
CLEAR_FEATURE (endpoint STALL) request has been received,
the next STALL will not be generated.
The DATA_END bit informs the USB FCU of the completion of the
process indicated in the SETUP packet. Set this bit to
“
1
”
when
the process requested in the SETUP packet is completed. (Con-
trol Read Transfer: set this bit after writing all of the requested
data to the FIFO; Control Write Transfer: set this bit to
“
1
”
after
reading all of the requested data from the FIFO.) When this bit is
“
1
”
, the host request is ignored and a STALL is returned. After the
status phase process is completed, the USB FCU automatically
clears it to
“
0
”
.
U
I
N
S
_
B
C
e
S
n
R
d
p
o
i
n
t
0
I
N
c
o
n
t
r
o
l
r
e
g
i
s
t
e
r
(
a
d
d
r
e
s
s
0
0
5
9
1
6
)
OUT_PKT_RDY flag (IN0CSR0)
0: Except the following condition (Cleared to
“
0
”
by writing
“
1
”
into
SERVICED_OUT_PKT_RDY bit)
1: End of a data packet reception
IN_PKT_RDY bit (IN0CSR1)
0: End of a data packet transmission
1: Write
“
1
”
at completion of writing a data packet into IN FIFO.
SEND_STALL bit (IN0CSR2)
0: Except the following condition
1: Transmitting STALL handshake signal
DATA_END bit (IN0CSR3)
0: Except the following condition (Cleared to
“
0
”
after completion of
status phase)
1: Write
“
1
”
at completion of writing or reading the last data packet
to/from FIFO.
FORCE_STALL flag (IN0CSR4)
0: Except the following condition
1: Protocol error detected
SETUP_END flag (IN0CSR5) (
Note
)
0: Except the following condition (Cleared to
“
0
”
by writing
“
1
”
into
SERVICED_SETUP_END bit)
1: Control transfer ends before the specific length of data is
transferred during the data phase.
SERVICED_OUT_PKT_RDY bit (IN0CSR6)
Writing
“
1
”
to this bit clears OUT_PKT_RDY flag to
“
0
”
.
SERVICED_SETUP_END bit (IN0CSR7)
Writing
“
1
”
to this bit clears SETUP_END flag to
“
0
”
.
b
0
b
7
N
o
t
e
:
I
f
t
h
i
s
b
i
t
i
s
s
e
t
t
o
“
0
”
,
s
t
o
p
a
c
c
e
s
s
i
n
g
t
h
e
F
I
F
O
t
o
s
e
r
v
e
t
h
e
p
r
e
v
i
o
u
s
s
e
t
u
p
t
r
a
n
s
a
c
t
i
o
n
.
Fig. 46 Structure of USB endpoint 0 IN control register
相關PDF資料
PDF描述
M37641F8HP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641M8-100FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641M8-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37702M2-127FP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37702S1AFP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
相關代理商/技術參數
參數描述
M37641F8FP#U0 功能描述:IC 740 MCU FLASH 32K 80QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/7600 標準包裝:250 系列:56F8xxx 核心處理器:56800E 芯體尺寸:16-位 速度:60MHz 連通性:CAN，SCI，SPI 外圍設備:POR，PWM，溫度傳感器，WDT 輸入/輸出數:21 程序存儲器容量:40KB（20K x 16） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:6K x 16 電壓 - 電源 (Vcc/Vdd):2.25 V ~ 3.6 V 數據轉換器:A/D 6x12b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:48-LQFP 包裝:托盤 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
M37641F8HP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8HP#U0 功能描述:IC 740 MCU FLASH 32K 80LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/7600 產品培訓模塊:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 標準包裝:27 系列:PIC® 24H 核心處理器:PIC 芯體尺寸:16-位 速度:40 MIP 連通性:I²C，SPI，UART/USART 外圍設備:欠壓檢測/復位，POR，PWM，WDT 輸入/輸出數:21 程序存儲器容量:12KB（4K x 24） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 3.6 V 數據轉換器:A/D 10x10b/12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 包裝:管件 產品目錄頁面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
M37641F8M8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8-XXXFP 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*