- 您現在的位置：買賣IC網 > PDF目錄45038 > M37906M6C-XXXSP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP42 PDF資料下載
參數資料
| 型號： | M37906M6C-XXXSP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP42 |
| 封裝： | 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-42 |
| 文件頁數： | 83/101頁 |
| 文件大?。?/td> | 766K |
| 代理商： | M37906M6C-XXXSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁當前第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
82
M37906M4C-XXXFP, M37906M4C-XXXSP, M37906M4H-XXXFP
M37906M4H-XXXSP, M37906M6C-XXXFP, M37906M6C-XXXSP
M37906M8C-XXXFP, M37906M8C-XXXSP
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Som
e param
etric
lim
its are
subject
to change.
16-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Fig. 89 Block diagram of debug function
Address compare register 0
Address compare register 1
Debug control register 0
Matching Compare register
Address matching
detect circuit
Debug control register 1
Internal data bus (DB0 to DB15)
CPU bus (Address)
Address matching
detection interrupt
DEBUG FUNCTION
When the CPU fetches an instruction code, an interrupt request will
be generated if a selected condition is satisfied, as a resultant of
comparison between a specified address and the start address
where the instruction code is stored (the contents of PG and PC).
The decision whether this condition is satisfied or not is called ad-
dress matching detection, and the interrupt generated by this detec-
tion is called an address matching detection interrupt. (For interrupt
vector addresses, refer to the section on interrupts.)
In the address matching detection, a non-maskable interrupt routine
is proceeded without execution of the original instruction which has
been allocated to the target address.
The debug function provides the following two modes:
the address matching detection mode, which is used to avoid the
area where program exists or modify a program.
the out-of-address-area detection mode, which is used to detect a
program runaway.
Figure 89 shows the block diagram of the debug function. Figures 90
and 91 show the bit configurations of the debug control registers 0,
1, and address compare registers 0,1, respectively.
The detect condition select bits of the debug control register 0 can
select one condition between the following 4 conditions. When the
selected address condition is satisfied, an address matching detec-
tion interrupt request will be generated:
(1) Address matching detection 0
The contents of PG and PC match with the address which has
been set in the address compare register 0.
(2) Address matching detection 1
The contents of PG and PC match with the address which has
been set in the address compare register 1.
(3) Address matching detection 2
The contents of PG and PC match with the address which has
been set in either of the address compare register 0 or address
compare register 1.
(4) Out-of-address-area detection
The contents of PG and PC are less than the address which has
been set in the address compare register 0 or larger than the ad-
dress which has been set in the address compare register 1.
By setting the detect enable bit of the debug control register 0 to “1”,
an address matching detection interrupt request will be generated if
any one of the above address conditions is satisfied. Clearing the
detect enable bit to “0” generates no interrupt request even if any of
the above address conditions is satisfied.
The address compare register access enable bit of the debug con-
trol register 1 must be set to “1” by the instruction just before the ac-
cess operation (read/write). Then, this bit must be cleared to “0”
(disabled) by the next instruction. While this bit = “0”, the address
compare registers 0, 1 cannot be accessed.
The address-matching-detection 2 decision bit of the debug control
register 1 decides, whether the address which has been set in the
address compare register 0 or 1 matches with the contents of PG,
PC, when the address matching detection 2 is selected. The con-
tents of this bit is invalid when address matching detection 0 or 1 is
selected.
In order to use the debug function to avoid the area where program
exists or modify a program, perform the necessary processing within
an address matching interrupt routine. As a result, the contents of
PG, PC, PS at acceptance of an address matching detection inter-
rupt request (i.e. the address at which an address matching detec-
tion condition is satisfied) have been pushed on to the stack. If a
return destination address after the interrupt processing is to be al-
tered, rewrite the contents of the stack, and then return by the RTI
instruction.
To use the debug function to detect a program runaway, set an ad-
dress area where no program exists into the address compare regis-
ters 0 and 1 by using the out-of-address-area detection. When the
CPU fetches instruction codes from this address area and executes
them, an address matching detection interrupt request will be gener-
ated.
The above debug function cannot be evaluated by a debugger, so
that the debug function must not be used while a debugger is run-
ning.
相關PDF資料 |
PDF描述 |
|---|---|
| M37906M4C-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDSO42 |
| M37906M4C-XXXSP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP42 |
| M37906M4H-XXXSP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP42 |
| M37920F8MHP | 16-BIT, FLASH, 26 MHz, MICROCONTROLLER, PQFP100 |
| M37920S4CGP | 16-BIT, 20 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37906M8C-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M8C-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906T-PRB | 功能描述:DEV POD PROBE FOR M37900T2-RPD-E RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M37920FCCGP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
| M37920FCCHP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
發布緊急采購，3分鐘左右您將得到回復。