參數資料
型號: M38049FFHKP
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 8.4 MHz, MICROCONTROLLER, PQFP64
封裝: 14 X 14 MM, 0.80 MM PITCH, PLASTIC, LQFP-64
文件頁數: 65/116頁
文件大?。?/td> 1261K
代理商: M38049FFHKP
Rev.1.01
Jan 25, 2005
page 52 of 114
REJ03B0131-0101Z
3804 Group (Spec. H)
3. SRDY3 output of reception side
q Note
When signals are output from the SRDY3 pin on the reception side
by using an external clock in the clock synchronous serial I/O
mode, set all of the receive enable bit, the SRDY3 output enable
bit, and the transmit enable bit to “1” (transmit enabled).
4. Setting serial I/O3 control register again
q Note
Set the serial I/O3 control register again after the transmission and
the reception circuits are reset by clearing both the transmit en-
able bit and the receive enable bit to “0.”
5. Data transmission control with referring to transmit shift
register completion flag
q Note
After the transmit data is written to the transmit buffer register, the
transmit shift register completion flag changes from “1” to “0” with
a delay of 0.5 to 1.5 shift clocks. When data transmission is con-
trolled with referring to the flag after writing the data to the transmit
buffer register, note the delay.
6. Transmission control when external clock is selected
q Note
When an external clock is used as the synchronous clock for data
transmission, set the transmit enable bit to “1” at “H” of the SCLK3
input level. Also, write data to the transmit buffer register at “H” of
the SCLK input level.
7. Transmit interrupt request when transmit enable bit is set
q Note
When using the transmit interrupt, take the following sequence.
Set the serial I/O3 transmit interrupt enable bit to “0” (disabled).
Set the transmit enable bit to “1”.
Set the serial I/O3 transmit interrupt request bit to “0” after 1 or
more instruction has executed.
Set the serial I/O3 transmit interrupt enable bit to “1” (enabled).
q Reason
When the transmit enable bit is set to “1”, the transmit buffer
empty flag and the transmit shift register shift completion flag are
also set to “1”. Therefore, regardless of selecting which timing for
the generating of transmit interrupts, the interrupt request is gener-
ated and the transmit interrupt request bit is set at this point.
Clear both the transmit enable bit
(TE) and the receive enable bit
(RE) to “0”
Set the bits 0 to 3 and bit 6 of the
serial I/O3 control register
Set both the transmit enable bit
(TE) and the receive enable bit
(RE), or one of them to “1”
Can be set with the
LDM instruction at the
same time
相關PDF資料
PDF描述
M38062E6FP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80
M38062E3-XXXFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80
M38062E6-XXXFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80
M38062M6-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP80
M38062E3FS 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC80
相關代理商/技術參數
參數描述
M38049FFLHP#U0 制造商:Renesas Electronics Corporation 功能描述:
M38049RLSS 功能描述:DEV EMULATOR CHIP RAM 2KB 64SDIP RoHS:否 類別:編程器,開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:*
M3806 功能描述:電纜固定件和配件 LTSCG 625 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度:
M3806 BK001 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 1000'
M3806 BK002 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 500'