- 您現在的位置：買賣IC網 > PDF目錄370954 > M3851 (Mitsubishi Electric Corporation) Single Chip 8 Bits Microcomputer(8位單片機) PDF資料下載
參數資料
| 型號： | M3851 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | Single Chip 8 Bits Microcomputer(8位單片機) |
| 中文描述： | 單芯片8位單片機（8位單片機） |
| 文件頁數： | 25/61頁 |
| 文件大?。?/td> | 904K |
| 代理商： | M3851 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁
25
3851 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Fig. 25 Interrupt request signal generating timing
Fig. 24 Structure of I
2
C status register
Bit 6: Communication mode specification bit (transfer direc-
tion specification bit: TRX)
This bit decides a direction of transfer for data communication.
When this bit is “0,” the reception mode is selected and the data of
a transmitting device is received. When the bit is “1,” the transmis-
sion mode is selected and address data and control data are
output onto the SDA in synchronization with the clock generated
on the S
CL
.
This bit is set/reset by software and hardware. About set/reset by
hardware is described below. This bit is set to “1” by hardware
when all the following conditions are satisfied:
When ALS is “0”
In the slave reception mode or the slave transmission mode
When the R/W bit reception is “1”
This bit is set to “0” in one of the following conditions:
When arbitration lost is detected.
When a STOP condition is detected.
When writing “1” to this bit by software is invalid by the START
condition duplication preventing function
(Note)
.
With MST = “0” and when a START condition is detected.
With MST = “0” and when ACK non-return is detected.
At reset
Bit 7: Communication mode specification bit (master/slave
specification bit: MST)
This bit is used for master/slave specification for data communica-
tion. When this bit is “0,” the slave is specified, so that a START
condition and a STOP condition generated by the master are re-
ceived, and data communication is performed in synchronization
with the clock generated by the master. When this bit is “1,” the
master is specified and a START condition and a STOP condition
are generated. Additionally, the clocks required for data communi-
cation are generated on the SCL.
This bit is set to “0” in one of the following conditions.
Immediately after completion of 1-byte data transfer when arbi-
tration lost is detected
When a STOP condition is detected.
Writing “1” to this bit by software is invalid by the START condi-
tion duplication preventing function
(Note)
.
At reset
Note:
START condition duplication preventing function
The MST, TRX, and BB bits is set to “1” at the same time after con-
firming that the BB flag is “0” in the procedure of a START condition
occurrence. However, when a START condition by another master
device occurs and the BB flag is set to “1” immediately after the con-
tents of the BB flag is confirmed, the START condition duplication
preventing function makes the writing to the MST and TRX bits in-
valid. The duplication preventing function becomes valid from the
rising of the BB flag to reception completion of slave address.
S
CL
PIN
IICIRQ
b7
MST
b0
I
2
C status register
(S1 : address 002D
16
)
Last receive bit
(Note)
0 : Last bit = “0”
1 : Last bit = “1”
General call detecting flag
(Note)
0 : No general call detected
1 : General call detected
Slave address comparison flag
(Note)
0 : Address disagreement
1 : Address agreement
Arbitration lost detecting flag
(Note)
0 : Not detected
1 : Detected
SCL pin low hold bit
0 : SCL pin low hold
1 : SCL pin low release
Bus busy flag
0 : Bus free
1 : Bus busy
Communication mode
specification bits
00 : Slave receive mode
01 : Slave transmit mode
10 : Master receive mode
11 : Master transmit mode
TRX BB PIN
AL AAS AD0 LRB
Note:
These bits and flags can be read out, but cannot
be written.
Write “0” to these bits at writing.
相關PDF資料 |
PDF描述 |
|---|---|
| M38512M4 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M388504E6SP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M388504E6SS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M3850 | Single Chip 8 Bits Microcomputer(8位單片機) |
| M388504E6FP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M3851 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 7COND 14AWG BLK 1000' |
| M3851 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 7COND 14AWG BLK 500' |
| M3851 BK005 | 制造商:Alpha Wire Company 功能描述:CBL 7COND 14AWG BLK 100' |
| M38510/00102BCB | 制造商:n/a 功能描述:38510/00102 S6I6B 制造商: 功能描述: 制造商:undefined 功能描述: |
| M38510/00103BCA | 制造商:QP Semiconductor 功能描述:NAND GATE, TRIPLE 3-INPUT |
發布緊急采購，3分鐘左右您將得到回復。