參數資料
型號: M41T00AUDD1E
廠商: STMICROELECTRONICS
元件分類: 時鐘/數據恢復及定時提取
英文描述: REAL TIME CLOCK, DSO16
封裝: 5 X 4 MM, ROHS COMPLIANT, DFN-16
文件頁數: 3/42頁
文件大?。?/td> 333K
代理商: M41T00AUDD1E
M41T00AUD
Operation
4.1
2-wire bus characteristics
This bus is intended for communication between different ICs. It consists of two lines: one
bi-directional for data signals (SDA) and one for clock signals (SCL). Both the SDA and the
SCL lines must be connected to a positive supply voltage via a pull-up resistor.
The following protocol has been defined:
Data transfer may be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is high.
Changes in the data line while the clock line is high will be interpreted as control
signals.
Accordingly, the following bus conditions have been defined:
Bus not busy. Both data and clock lines remain high.
Start data transfer. A change in the state of the data line, from high to low, while the
clock is high, defines the START condition.
Stop data transfer. A change in the state of the data line, from low to high, while the
clock is high, defines the STOP condition.
Data valid. The state of the data line represents valid data when after a start condition,
the data line is stable for the duration of the high period of the clock signal. The data on
the line may be changed during the low period of the clock signal. There is one clock
pulse per bit of data.
Each data transfer is initiated with a start condition and terminated with a stop condition.
The number of data bytes transferred between the start and stop conditions is not limited.
The information is transmitted byte-wide and each receiver acknowledges with a ninth bit.
By definition, a device that gives out a message is called "transmitter", the receiving device
that gets the message is called "receiver". The device that controls the message is called
"master". The devices that are controlled by the master are called "slaves".
Acknowledge. Each byte of eight bits is followed by one acknowledge bit. This
acknowledge bit is a low level put on the bus by the receiver, whereas the master
generates an extra acknowledge related clock pulse.
A slave receiver which is addressed is obliged to generate an acknowledge after the
reception of each byte. Also, a master receiver must generate an acknowledge after the
reception of each byte that has been clocked out of the slave transmitter.
The device that acknowledges has to pull down the SDA line during the acknowledge clock
pulse in such a way that the SDA line is a stable Low during the high period of the
acknowledge related clock pulse. Of course, setup and hold times must be taken into
account. A master receiver must signal an end-of-data to the slave transmitter by not
generating an acknowledge on the last byte that has been clocked out of the slave. In this
case, the transmitter must leave the data line high to enable the master to generate the
STOP condition.
相關PDF資料
PDF描述
M43E-12-52 PLCC52, IC SOCKET
M43E-10-100 PLCC100, IC SOCKET
M43E-12-68 PLCC68, IC SOCKET
M43E-14-28 PLCC28, IC SOCKET
M43E-14-44 PLCC44, IC SOCKET
相關代理商/技術參數
參數描述
M41T00AUDD1F 功能描述:實時時鐘 SERIAL RTC W/AUDIO RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T00CAP 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial access real-time clock (RTC) with integral backup battery and crystal
M41T00CAPPC1 制造商:STMicroelectronics 功能描述:REAL TIME CLOCK SERL 8BYTE 16DFN - Bulk 制造商:STMicroelectronics 功能描述:IC RTC SERIAL W/AUDIO 24PDIP
M41T00M 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Serial Access TIMEKEEPER
M41T00M6 功能描述:實時時鐘 Serial 64 (8X8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube