參數資料
型號： MA160014
廠商： Microchip Technology
文件頁數： 28/71頁
文件大小： 0K
描述： MOD PLUG-IN 44PIN PIC18LF45K22
標準包裝： 1
系列： PIC® XLP™ 18F
附件類型： 插拔式模塊（PIM）- PIC18LF45K22
適用于相關產品： PICDEM PIC18 Explorer，DM183032
PIC18(L)F2X/4XK22
DS41412E-page 34
2010-2012 Microchip Technology Inc.
2.4
Clock Source Modes
Clock Source modes can be classified as external or
internal.
External Clock modes rely on external circuitry for
the clock source. Examples are: Clock modules
(EC mode), quartz crystal resonators or ceramic
resonators (LP, XT and HS modes) and Resistor-
Capacitor (RC mode) circuits.
Internal clock sources are contained internally
within the Oscillator block. The Oscillator block
has three internal oscillators: the 16 MHz High-
Frequency Internal Oscillator (HFINTOSC),
500 kHz Medium-Frequency Internal Oscillator
(MFINTOSC) and the 31.25 kHz Low-Frequency
Internal Oscillator (LFINTOSC).
The system clock can be selected between external or
internal clock sources via the System Clock Select
(SCS<1:0>) bits of the OSCCON register. See
for
additional
information.
2.5
External Clock Modes
2.5.1
OSCILLATOR START-UP TIMER (OST)
When the oscillator module is configured for LP, XT or
HS modes, the Oscillator Start-up Timer (OST) counts
1024 oscillations from OSC1. This occurs following a
Power-on Reset (POR) and when the Power-up Timer
(PWRT) has expired (if configured), or a wake-up from
Sleep. During this time, the program counter does not
increment and program execution is suspended. The
OST ensures that the oscillator circuit, using a quartz
crystal resonator or ceramic resonator, has started and
is providing a stable system clock to the oscillator
module. When switching between clock sources, a
delay is required to allow the new clock to stabilize.
These oscillator delays are shown in Table 2-2.
In order to minimize latency between external oscillator
start-up and code execution, the Two-Speed Clock
Start-up mode can be selected (see Section 2.12
TABLE 2-2:
OSCILLATOR DELAY EXAMPLES
2.5.2
EC MODE
The External Clock (EC) mode allows an externally
generated logic level as the system clock source. When
operating in this mode, an external clock source is
connected to the OSC1 input and the OSC2 is available
for general purpose I/O. Figure 2-5 shows the pin
connections for EC mode.
The External Clock (EC) offers different power modes,
Low Power (ECLP), Medium Power (ECMP) and High
Power (ECHP), selectable by the FOSC<3:0> bits.
Each mode is best suited for a certain range of
frequencies. The ranges are:
ECLP – below 500 kHz
ECMP – between 500 kHz and 16 MHz
ECHP – above 16 MHz
The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
operation after a Power-on Reset (POR) or wake-up
from Sleep. Because the PIC MCU design is fully
static, stopping the external clock input will have the
effect of halting the device while leaving all data intact.
Upon restarting the external clock, the device will
resume operation as if no time had elapsed.
FIGURE 2-5:
EXTERNAL CLOCK (EC)
MODE OPERATION
Switch From
Switch To
Frequency
Oscillator Delay
Sleep/POR
LFINTOSC
MFINTOSC
HFINTOSC
31.25 kHz
31.25 kHz to 500 kHz
31.25 kHz to 16 MHz
Oscillator Warm-Up Delay (TWARM)
Sleep/POR
EC, RC
DC – 64 MHz
2 instruction cycles
LFINTOSC (31.25 kHz)
EC, RC
DC – 64 MHz
1 cycle of each
Sleep/POR
LP, XT, HS
32 kHz to 40 MHz
1024 Clock Cycles (OST)
Sleep/POR
4xPLL
32 MHz to 64 MHz
1024 Clock Cycles (OST) + 2 ms
LFINTOSC (31.25 kHz)
LFINTOSC
HFINTOSC
31.25 kHz to 16 MHz
1
s (approx.)
OSC1/CLKIN
OSC2/CLKOUT(1)
I/O
Clock from
Ext. System
PIC MCU
Note
1:
Alternate pin functions are listed in
相關PDF資料
PDF描述
1-1589476-5 CONN RCPT 15POS 30AWG 30IN
MAX1607ESA+T IC SW USB CURRENT LIMIT 8SOIC
MA180023 MODULE PLUG-IN PIC18F46J11 PIM
1-1589476-8 CONN RCPT 15POS 32AWG 24IN
0210490389 CABLE JUMPER 1.25MM .051M 32POS
相關代理商/技術參數
參數描述
MA160015 功能描述:子卡和OEM板 PIC16LF1947 PIM RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
MA160016 功能描述:子卡和OEM板 PIC16F1947 PIM RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
MA161 制造商:Panasonic Industrial Company 功能描述:DIODE
MA16101BAN 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:HIGH FREQUENCY CERAMIC CAPACITORS
MA16101BBN 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:HIGH FREQUENCY CERAMIC CAPACITORS
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*