- 您現在的位置：買賣IC網 > PDF目錄16967 > MA160014 (Microchip Technology)MOD PLUG-IN 44PIN PIC18LF45K22 PDF資料下載
參數資料
| 型號： | MA160014 |
| 廠商： | Microchip Technology |
| 文件頁數： | 57/71頁 |
| 文件大?。?/td> | 0K |
| 描述： | MOD PLUG-IN 44PIN PIC18LF45K22 |
| 標準包裝： | 1 |
| 系列： | PIC® XLP™ 18F |
| 附件類型： | 插拔式模塊（PIM）- PIC18LF45K22 |
| 適用于相關產品： | PICDEM PIC18 Explorer，DM183032 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁當前第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁
PIC18(L)F2X/4XK22
DS41412F-page 60
2010-2012 Microchip Technology Inc.
4.2
Register Definitions: Reset Control
REGISTER 4-1:
RCON: RESET CONTROL REGISTER
R/W-0/0
R/W-q/u
U-0
R/W-1/q
R-1/q
R/W-q/u
R/W-0/q
IPEN
SBOREN(1)
—RI
TO
PD
POR(2)
BOR
bit 7
bit 0
Legend:
R = Readable bit
W = Writable bit
U = Unimplemented bit, read as ‘0’
‘1’ = Bit is set
‘0’ = Bit is cleared
-n/n = Value at POR and BOR/Value at all other Resets
x = Bit is unknown
u = unchanged
q = depends on condition
bit 7
IPEN: Interrupt Priority Enable bit
1
= Enable priority levels on interrupts
0
= Disable priority levels on interrupts (PIC16CXXX Compatibility mode)
bit 6
SBOREN: BOR Software Enable bit(1)
If BOREN<1:0> = 01:
1
= BOR is enabled
0
= BOR is disabled
If BOREN<1:0> = 00, 10 or 11:
Bit is disabled and read as ‘0’.
bit 5
Unimplemented: Read as ‘0’
bit 4
RI: RESET Instruction Flag bit
1
= The RESET instruction was not executed (set by firmware or Power-on Reset)
0
= The RESET instruction was executed causing a device Reset (must be set in firmware after a
code-executed Reset occurs)
bit 3
TO: Watchdog Time-out Flag bit
1
= Set by power-up, CLRWDT instruction or SLEEP instruction
0
= A WDT time-out occurred
bit 2
PD: Power-down Detection Flag bit
1
= Set by power-up or by the CLRWDT instruction
0
= Set by execution of the SLEEP instruction
bit 1
POR: Power-on Reset Status bit(2)
1
= No Power-on Reset occurred
0
= A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
bit 0
BOR: Brown-out Reset Status bit(3)
1
= A Brown-out Reset has not occurred (set by firmware only)
0
= A Brown-out Reset occurred (must be set by firmware after a POR or Brown-out Reset occurs)
Note 1:
When CONFIG2L[2:1] = 01, then the SBOREN Reset state is ‘1’; otherwise, it is ‘0’.
2:
The actual Reset value of POR is determined by the type of device Reset. See the notes following this
register and Section 4.7 “Reset State of Registers” for additional information.
3:
See Table 4-1.
Note 1: Brown-out Reset is indicated when BOR is ‘0’ and POR is ‘1’ (assuming that both POR and BOR were set
to ‘1’ by firmware immediately after POR).
2: It is recommended that the POR bit be set after a Power-on Reset has been detected so that subsequent
Power-on Resets may be detected.
相關PDF資料 |
PDF描述 |
|---|---|
| 1-1589476-5 | CONN RCPT 15POS 30AWG 30IN |
| MAX1607ESA+T | IC SW USB CURRENT LIMIT 8SOIC |
| MA180023 | MODULE PLUG-IN PIC18F46J11 PIM |
| 1-1589476-8 | CONN RCPT 15POS 32AWG 24IN |
| 0210490389 | CABLE JUMPER 1.25MM .051M 32POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MA160015 | 功能描述:子卡和OEM板 PIC16LF1947 PIM RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MA160016 | 功能描述:子卡和OEM板 PIC16F1947 PIM RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit |
| MA161 | 制造商:Panasonic Industrial Company 功能描述:DIODE |
| MA16101BAN | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:HIGH FREQUENCY CERAMIC CAPACITORS |
| MA16101BBN | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:HIGH FREQUENCY CERAMIC CAPACITORS |
發布緊急采購，3分鐘左右您將得到回復。