- 您現在的位置：買賣IC網 > PDF目錄9462 > MAX127ACAI+T (Maxim Integrated Products)IC DAS 12BIT 2-WIRE 28-SSOP PDF資料下載
參數資料
| 型號： | MAX127ACAI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 16/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAS 12BIT 2-WIRE 28-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 類型： | 數據采集系統（DAS），ADC |
| 分辨率（位）： | 12 b |
| 采樣率（每秒）： | 8k |
| 數據接口： | I²C，串行 |
| 電壓電源： | 單電源 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 帶卷 (TR) |
MAX127/MAX128
Multirange, +5V, 12-Bit DAS with
2-Wire Serial Interface
_______________________________________________________________________________________
9
Detailed Description
Converter Operation
The MAX127/MAX128 multirange, fault-tolerant ADCs
use successive approximation and internal track/hold
(T/H) circuitry to convert an analog signal to a 12-bit
digital output. Figure 1 shows the block diagram for
these devices.
Analog-Input Track/Hold
The T/H circuitry enters its tracking/acquisition mode on
the falling edge of the sixth clock in the 8-bit input con-
trol word and enters its hold/conversion mode when the
master issues a STOP condition. For timing information,
see the
Start a Conversion section.
Input Range and Protection
The MAX127/MAX128 have software-selectable input
ranges. Each analog input channel can be indepen-
dently programmed to one of four ranges by setting the
appropriate control bits (RNG, BIP) in the control byte
(Table 1). The MAX127 has selectable input ranges
extending to ±10V (±VREF x 2.441), while the MAX128
has selectable input ranges extending to ±VREF. Note
that when an external reference is applied at REFADJ,
the voltage at REF is given by VREF = 1.638 x VREFADJ
(2.4 < VREF < 4.18). Figure 2 shows the equivalent
input circuit.
A resistor network on each analog input provides a
±16.5V fault protection for all channels. This circuit lim-
its the current going into or out of the pin to less than
1.2mA, whether or not the channel is on. This provides
an added layer of protection when momentary over-
voltages occur at the selected input channel, and when
a negative signal is applied at the input even though
the device may be configured for unipolar mode.
Overvoltage protection is active even if the device is in
power-down mode or VDD = 0.
Digital Interface
The MAX127/MAX128 feature a 2-wire serial interface
consisting of the SDA and SCL pins. SDA is the data
I/O and SCL is the serial clock input, controlled by the
master device. A2–A0 are used to program the
MAX127/MAX128 to different slave addresses. (The
MAX127/MAX128 only work as slaves.) The two bus
lines (SDA and SCL) must be high when the bus is not
in use. External pull-up resistors (1k
or greater) are
required on SDA and SCL to maintain I2C compatibility.
Table 1 shows the input control-byte format.
Figure 1. Block Diagram
CH2
CH1
CH0
SHDN
CH3
CH4
CH5
CH6
CH7
REFADJ
REF
VDD
AGND
DGND
MAX127
MAX128
12-BIT SAR ADC
IN
REF
CLOCK
OUT
T/H
2.5V
REFERENCE
ANALOG
INPUT
MUX
AND SIGNAL
CONDITIONING
AV =
1.638
INT
CLOCK
SDA
A2
A1
A0
SCL
SERIAL INTERFACE LOGIC
10k
Figure 2. Equivalent Input Circuit
5.12k
R2
R1
CH_
S1
S2
S3
S4
BIPOLAR
UNIPOLAR
VOLTAGE
REFERENCE
T/H
OUT
HOLD
TRACK
HOLD
OFF
ON
CHOLD
S1 = BIPOLAR/UNIPOLAR SWITCH
S2 = INPUT MUX SWITCH
S3, S4 = T/H SWITCH
R1 = 12.5k
(MAX127) OR 5.12k (MAX128)
R2 = 8.67k
(MAX127) OR ∞ (MAX128)
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B4N-IU-F2 | CONVERTER MOD DC/DC 18.5V 200W |
| VE-B4M-IU-F4 | CONVERTER MOD DC/DC 10V 200W |
| VE-B4M-IU-F3 | CONVERTER MOD DC/DC 10V 200W |
| M83723/84R1212N | CONN RCPT 12POS JAM NUT W/SCKT |
| VE-B4M-IU-F1 | CONVERTER MOD DC/DC 10V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX127ACNG | 功能描述:數據轉換系統 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127ACNG+ | 功能描述:數據轉換系統 12-Bit 8Ch 8ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127AEAI | 功能描述:數據轉換系統 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127AEAI/GH9 | 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127AEAI/GH9-T | 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。