- 您現在的位置：買賣IC網 > PDF目錄9462 > MAX127ACAI+T (Maxim Integrated Products)IC DAS 12BIT 2-WIRE 28-SSOP PDF資料下載
參數資料
| 型號： | MAX127ACAI+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAS 12BIT 2-WIRE 28-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,000 |
| 類型： | 數據采集系統（DAS），ADC |
| 分辨率（位）： | 12 b |
| 采樣率（每秒）： | 8k |
| 數據接口： | I²C，串行 |
| 電壓電源： | 單電源 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 帶卷 (TR) |
The MAX127/MAX128 ignore acknowledge and NOT-
acknowledge conditions issued by the master during
the read cycle. The device waits for the master to read
the output data or waits until a STOP condition is
issued. Figure 10 shows a complete read cycle.
In unipolar input mode, the output is straight binary. For
bipolar input mode, the output is two’s complement. For
output binary codes see the
Transfer Function section.
Applications Information
Power-On Reset
The MAX127/MAX128 power up in normal operating
mode, waiting for a START condition followed by the
appropriate slave address. The contents of the input
and output data registers are cleared at power-up.
Internal or External Reference
The MAX127/MAX128 operate with either an internal or
an external reference (Figures 11a–11c). An external
reference is connected to either REF or to REFADJ.
The REFADJ internal buffer gain is trimmed to 1.6384 to
provide 4.096V at REF from a 2.5V reference.
Internal Reference
The internally trimmed 2.50V reference is amplified
through the REFADJ buffer to provide 4.096V at REF.
Bypass REF with a 4.7F capacitor to AGND and bypass
REFADJ with a 0.01F capacitor to AGND (Figure 11a).
The internal reference voltage is adjustable to ±1.5%
(±65 LSBs) with the reference-adjust circuit of Figure 12.
External Reference
To use the REF input directly, disable the internal buffer
by connecting REFADJ to VDD (Figure 11b). Using the
REFADJ input eliminates the need to buffer the refer-
ence externally. When the reference is applied at
REFADJ, bypass REFADJ with a 0.01F capacitor to
AGND (Figure 11c).
At REF and REFADJ, the input impedance is a mini-
mum of 10k
for DC currents. During conversions, an
external reference at REF must be able to drive a
400A DC load, and must have an output impedance
of 10
or less. If the reference has higher input imped-
ance or is noisy, bypass REF with a 4.7F capacitor to
AGND as close to the chip as possible.
With an external reference voltage of less than 4.096V
at REF or less than 2.5V at REFADJ, the increase in
RMS noise to the LSB value (full-scale voltage/4096)
results in performance degradation and loss of effec-
tive bits.
Power-Down Mode
To save power, put the converter into low-current shut-
down mode between conversions. Two programmable
power-down modes are available, in addition to the
hardware shutdown. Select STBYPD or FULLPD by pro-
gramming PD0 and PD1 in the input control byte (Table
4). When software power-down is asserted, it becomes
effective only after the end of conversion. In all power-
down modes, the interface remains active and conver-
sion results may be read. Input overvoltage protection
is active in all power-down modes.
MAX127/MAX128
Multirange, +5V, 12-Bit DAS with
2-Wire Serial Interface
______________________________________________________________________________________
13
Figure 10. Complete 2-Wire Serial Read Transmission
START
CONDITION
STOP
CONDITION
LSB DATA BYTE
MSB DATA BYTE
SLAVE ADDRESS BYTE
MSB
LSB
0
1
2
7
8
9
10
11
17
18
19
22
23
26
27
R
A
D11
D4
A
D3
D0
A
FILLED WITH
4 ZEROS
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B4N-IU-F2 | CONVERTER MOD DC/DC 18.5V 200W |
| VE-B4M-IU-F4 | CONVERTER MOD DC/DC 10V 200W |
| VE-B4M-IU-F3 | CONVERTER MOD DC/DC 10V 200W |
| M83723/84R1212N | CONN RCPT 12POS JAM NUT W/SCKT |
| VE-B4M-IU-F1 | CONVERTER MOD DC/DC 10V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX127ACNG | 功能描述:數據轉換系統 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127ACNG+ | 功能描述:數據轉換系統 12-Bit 8Ch 8ksps 4.18V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127AEAI | 功能描述:數據轉換系統 Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127AEAI/GH9 | 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| MAX127AEAI/GH9-T | 功能描述:數據轉換系統 RoHS:否 制造商:Texas Instruments 轉換速率:0.001 MSPs 分辨率:24 bit 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。