參數資料
型號: MAX19516ETM+T
廠商: Maxim Integrated Products
文件頁數: 26/35頁
文件大小: 0K
描述: IC ADC 10BIT 2CH 100MSPS 48TQFN
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
位數: 10
采樣率(每秒): 100M
數據接口: 串行,并聯
轉換器數目: 2
電壓電源: 模擬和數字
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 48-WFQFN 裸露焊盤
供應商設備封裝: 48-TQFN-EP(7x7)
包裝: 帶卷 (TR)
輸入數目和類型: 4 個單端,單極;2 個差分,單極
MAX19516
Dual-Channel, 10-Bit, 100Msps ADC
32
______________________________________________________________________________________
The circuit of Figure 19 also converts a single-ended
input signal to a fully differential signal. Figure 19 uti-
lizes an additional transformer to improve the common-
mode rejection allowing high-frequency signals beyond
the Nyquist frequency. A set of 75
and 110 termina-
tion resistors provide an equivalent 50
termination to
the signal source. The second set of termination resis-
tors connect to CM_ providing the correct input com-
mon-mode voltage.
Single-Ended AC-Coupled Input Signal
Figure 20 shows a single-ended, AC-coupled input
application. The MAX4108 provides high speed, high
bandwidth, low noise, and low distortion to maintain the
input signal integrity. Bias voltage is applied to the
inputs through internal 2k
resistors. See Common
Mode register 08h for further details.
DC-Coupled Input
The MAX19516’s wide common-mode voltage range
(0.4V to 1.4V) allows DC-coupled signals. Ensure that the
common-mode voltage remains between 0.4V and 1.4V.
Clock Input
Figure 21 shows a single-ended-to-differential clock
input converting circuit.
Grounding, Bypassing, and
Board-Layout Considerations
The MAX19516 requires high-speed board-layout
design techniques. Locate all bypass capacitors as
close as possible to the device, preferably on the same
side as the ADC, using surface-mount devices for mini-
mum inductance. Bypass AVDD, OVDD, REFIO, CMA,
and CMB with 0.1F ceramic capacitors to GND.
Multilayer boards with ground and power planes
produce the highest level of signal integrity. Route high-
speed digital signal traces away from the sensitive ana-
log traces of either channel. Make sure to isolate the
analog input lines to each respective converter to mini-
mize channel-to-channel crosstalk. Keep all signal lines
short and free of 90° turns.
Definitions
Integral Nonlinearity (INL)
INL is the deviation of the measured transfer function
from a best-fit straight line. Worst-case deviation is
defined as INL.
Differential Nonlinearity (DNL)
DNL is the difference between the measured transfer
function step width and the ideal value of 1 LSB. A DNL
error specification of less than 1 LSB guarantees no
missing codes and a monotonic transfer function. DNL
deviations are measured at each step of the transfer
function and the worst-case deviation is defined as DNL.
Offset Error
Offset error is a parameter that indicates how well the
actual transfer function matches the ideal transfer func-
tion at midscale. Ideally, the midscale transition occurs
at 0.5 LSB above midscale. The offset error is the
amount of deviation between the measured midscale
transition point and the ideal midscale transition point.
Gain Error
Gain error is a figure of merit that indicates how well the
slope of the measured transfer function matches the
slope of the ideal transfer function based on the speci-
fied full-scale input-voltage range. The gain error is
defined as the relative error of the measured transfer
function and is expressed as a percentage.
Figure 20. Single-Ended, AC-Coupled Input Drive
MAX19516
0.1
F
100
100
0.1
F
IN_+
CM_
0.1
F
IN_-
MAX4108
VIN
Figure 21. Single-Ended-to-Differential Clock Input
MAX19516
49.9
49.9
0.01
F
0.1
F
0.01
F
CLK+
CLK-
CLKIN
相關PDF資料
PDF描述
MAX19700ETM+T IC ANLG FRNT END 48-TQFN
MAX19705ETM+ IC ANLG FRNT END 48-TQFN
MAX19706ETM+T IC ANLG FRNT END 48-TQFN
MAX19707ETM+T IC ANLG FRNT END 48-TQFN
MAX19708ETM+ IC ANLG FRONT END 11MSPS 48-TQFN
相關代理商/技術參數
參數描述
MAX19516EVKIT+ 功能描述:數據轉換 IC 開發工具 MAX19505-07/15-17 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX19517ETM+ 功能描述:模數轉換器 - ADC 10-Bit 2Ch 130Msps 1.8V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX19517ETM+T 功能描述:模數轉換器 - ADC 10-Bit 2Ch 130Msps 1.8V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX19517EVKIT+ 功能描述:數據轉換 IC 開發工具 MAX19517 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX1951AESA+ 功能描述:直流/直流開關調節器 1MHz 2A 2.6-5.5V PWM DC/DC Step-Down RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5