參數資料
型號: MAX3676EHJ+
廠商: Maxim Integrated Products
文件頁數: 5/15頁
文件大?。?/td> 0K
描述: IC CLOCK RECOVERY 32-TQFP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 360
類型: 時鐘和數據恢復(CDR),多路復用器
PLL:
主要目的: SONET/SDH
輸入: PECL
輸出: PECL
電路數: 1
比率 - 輸入:輸出: 2:2
差分 - 輸入:輸出: 是/是
頻率 - 最大: 622.08MHz
電源電壓: 3 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 32-TQFP
供應商設備封裝: 32-TQFP(5x5)
包裝: 托盤
MAX3676
622Mbps, 3.3V Clock-Recovery and
Data-Retiming IC with Limiting Amplifier
______________________________________________________________________________________
13
allowable pattern-dependent jitter, peak-to-peak
(seconds); and BW = typical system bandwidth, nor-
mally 0.6 to 1.0 times the data rate (Hertz). If the PDJ is
still larger than desired, continue increasing the value of
CIN. Note that to maintain stability when using the
MAX3676 analog inputs (ADI+, ADI-), it is important to
keep the low-frequency cutoff associated with COLC
below the corner frequency associated with CIN (fC)
(Table 1).
PDJ can also be present due to insufficient high-fre-
quency bandwidth (Figure 10). If the amplifiers are not
fast enough to allow for complete transitions during sin-
gle-bit patterns, or if the amplifier does not allow ade-
quate settling time, high-frequency PDJ can result.
Pulse-Width Distortion
Finally, PWD occurs when the midpoint crossing of a
0–1 transition and a 1–0 transition does not occur at the
same level (Figure 11). DC offsets and nonsymmetrical
rising and falling edge speeds both contribute to PWD.
For a 1–0 bit stream, calculate PWD as follows:
PWD = [(width of wider pulse) -
(width of narrower pulse)]/2
Phase Adjust
The internal clock and data alignment in the MAX3676
is well maintained close to the center of the data eye.
Although not required, this sampling point can be shift-
ed using the PHADJ inputs to optimize BER perfor-
mance. The PHADJ inputs operate with differential
input signals to approximately ±1V. A simple resistor
divider with a bypass capacitor is sufficient to set up
these levels. When the PHADJ inputs are not used, they
should be tied directly to VCC.
Figure 10. Pattern-Dependent Jitter Due to High-Frequency
Rolloff
AMPLITUDE
TIME
MIDPOINT
LONG
CONSECUTIVE
BIT STREAM
0-1-0 BIT STREAM
HF PDJ
Figure 11. Pulse-Width Distortion
AMPLITUDE
TIME
MIDPOINT
WIDTH OF A ONE
WIDTH OF A ZERO
PWD RESULTS WHEN THE WIDTH
OF A ZERO DOES NOT EQUAL
THE WIDTH OF A ONE.
tFALL
≠ tRISE
相關PDF資料
PDF描述
ADN2813ACPZ IC CLK/DATA REC 1.25GBPS 48LFCSP
AD800-52BRZ IC CLK\DATA RECOVERY PLL 20SOIC
SY87700VZH IC CLK/DATA RECOVERY 3.3V 28SOIC
MS27467P25B35PC CONN PLUG 128POS STRAIGHT W/PINS
AD9558BCPZ IC CLOCK TRANSLATOR 64LFCSP
相關代理商/技術參數
參數描述
MAX3676EHJ+ 功能描述:時鐘發生器及支持產品 622Mbps 3.3V Clock Recovery RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
MAX3676EHJ+T 功能描述:時鐘發生器及支持產品 622Mbps 3.3V Clock Recovery RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
MAX3676EHJ-T 功能描述:時鐘發生器及支持產品 622Mbps 3.3V Clock Recovery RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56
MAX3677CTJ+ 制造商:Microsemi Corporation 功能描述:+3.3V, LOW-JITTER CLOCK GEN W/MULT OUT - Trays 制造商:Microsemi Corporation 功能描述:Microsemi MAX3677CTJ+ Clocks - Timers 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CLOCK GENERATOR PROGR 32TQFN 制造商:Microsemi Corporation 功能描述:IC CLOCK GENERATOR PROGR 32TQFN
MAX3677CTJ+T 制造商:Microsemi Corporation 功能描述:+3.3V, LOW-JITTER CLOCK GEN W/MULT OUT - Tape and Reel