- 您現在的位置：買賣IC網 > PDF目錄5814 > MAX3798ETJ+ (Maxim Integrated Products)IC LIMITING AMP/VCSEL DVR 32TQFN PDF資料下載
參數資料
| 型號： | MAX3798ETJ+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 13/35頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIMITING AMP/VCSEL DVR 32TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 放大器類型： | 限制 |
| 電路數： | 1 |
| 輸出類型： | 差分 |
| 電流 - 電源： | 97mA |
| 電壓 - 電源，單路/雙路(±)： | 2.85 V ~ 3.63 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-TQFN-EP（5x5） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1387 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
MAX3798
3-Wire Digital Communication
The MAX3798 implements a proprietary 3-wire digital
interface. An external controller generates the clock. The
3-wire interface consists of an SDA bidirectional data
line, an SCL clock signal input, and a CSEL chip-select
input (active high). The external master initiates a data
transfer by asserting the CSEL pin. The master starts to
generate a clock signal after the CSEL pin has been set
to 1. All data transfers are most significant bit (MSB) first.
Protocol
Each operation consists of 16-bit transfers (15-bit
address/data, 1-bit RWN). The bus master generates
16 clock cycles to SCL. All operations transfer 8 bits to
the MAX3798. The RWN bit determines if the cycle is
read or write. See Table 4.
Register Addresses
The MAX3798 contains 17 registers available for pro-
gramming. Table 5 shows the registers and addresses.
Write Mode (RWN = 0)
The master generates 16 clock cycles at SCL in total.
The master outputs a total of 16 bits (MSB first) to the
SDA line at the falling edge of the clock. The master
closes the transmission by setting CSEL to 0. Figure 4
shows the interface timing.
Read Mode (RWN = 1)
The master generates 16 clock cycles at SCL in total.
The master outputs a total of 8 bits (MSB first) to the
SDA line at the falling edge of the clock. The SDA line is
released after the RWN bit has been transmitted. The
slave outputs 8 bits of data (MSB first) at the rising edge
of the clock. The master closes the transmission by set-
ting CSEL to 0. Figure 4 shows the interface timing.
Mode Control
Normal mode allows read-only instruction for all regis-
ters except MODINC and BIASINC. The MODINC and
BIASINC registers can be updated during normal
mode. Doing so speeds up the laser control update
through the 3-wire interface by a factor of two. The nor-
mal mode is the default mode.
Setup mode allows the master to write unrestricted data
into any register except the status (TXSTAT1, TXSTAT2,
and RXSTAT) registers. To enter the setup mode, the
MODECTRL register (address = H0x0E) must be set to
H0x12. After the MODECTRL register has been set to
H0x12, the next operation is unrestricted. The setup
mode is automatically exited after the next operation is
finished. This sequence must be repeated if further
unrestricted settings are necessary.
1.0625Gbps to 10.32Gbps, Integrated, Low-
Power SFP+ Limiting Amplifier and VCSEL Driver
20
______________________________________________________________________________________
PIN
NAME
SHORT TO VCC
SHORT TO GND
OPEN
31
CAZ2
Normal (Note 1)
32
CAZ1
(VEER)
Disabled—Fault (external supply
shorted) (Note 2)
Normal (Note 3)—Redundant path
Table 3. Circuit Response to Single-Point Faults (continued)
BIT
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Register Address
RWN
Data that is written or read.
Table 4. Digital Communication Word Structure
Note 1: Normal—Does not affect laser power.
Note 2: Supply-shorted current is assumed to be primarily on the circuit board (outside this device) and the main supply is
collapsed by the short.
Note 3: Normal in functionality, but performance could be affected.
Warning: Shorted to VCC or shorted to ground on some pins can violate the Absolute Maximum Ratings.
相關PDF資料 |
PDF描述 |
|---|---|
| BK1/S506-6.3-R | FUSE 6.3A 250V TLAG GLS 5X20 IEC |
| BK/S506-5-R | FUSE 5A 250V T-LAG GLASS S506 |
| 2095-300-BLF | SURGE ARRESTOR GDT 3000V AXIAL |
| BK/ATC-1 | FUSE BLADE 1A 32V BLACK UL |
| 2095-200-BLF | SURGE ARRESTOR GDT 2000V AXIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX3798ETJ+ | 功能描述:激光驅動器 1.0625-10.32Gbps SFP w/VCSEL Driver RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3798ETJ+T | 功能描述:激光驅動器 1.0625-10.32Gbps SFP w/VCSEL Driver RoHS:否 制造商:Micrel 數據速率:4.25 Gbps 工作電源電壓:3 V to 3.6 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-16 封裝:Tube |
| MAX3799E/D | 功能描述:限幅放大器 1Gbps to 14Gbps SFP+ Multirate Limiting Amplifier and VCSEL Driver RoHS:否 制造商:Micrel 輸入電壓范圍（最大值）:3.6 V 工作電源電壓:3.3 V 電源電流:40 mA 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Tube |
| MAX3799ETJ+ | 功能描述:限幅放大器 1-14Gbps SFP w/VCSEL Driver RoHS:否 制造商:Micrel 輸入電壓范圍（最大值）:3.6 V 工作電源電壓:3.3 V 電源電流:40 mA 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Tube |
| MAX3799ETJ+T | 功能描述:限幅放大器 1-14Gbps SFP w/VCSEL Driver RoHS:否 制造商:Micrel 輸入電壓范圍（最大值）:3.6 V 工作電源電壓:3.3 V 電源電流:40 mA 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:MSOP-10 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。