- 您現在的位置：買賣IC網 > PDF目錄11560 > MAX5945EAX+T (Maxim Integrated Products)IC NETWORK PWR CTRL 36-SSOP PDF資料下載
參數資料
| 型號： | MAX5945EAX+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC NETWORK PWR CTRL 36-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 控制器類型： | 網絡電源控制器 |
| 接口： | I²C |
| 電源電壓： | 3.3V |
| 電流 - 電源： | 4.2mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-BSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 36-SSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
agement where it detects a PD that draws more current
than the allowable amount for its class. The MAX5945’s
extensive programmability enhances system flexibility
and allows for uses in other applications.
The MAX5945 has four different operating modes: auto
mode, semi-auto mode, manual mode, and shutdown
mode (see the Operation Modes section). A special
watchdog feature allows the hardware to gracefully
take over control if the software/firmware crashes. A
cadence timing feature allows the MAX5945 to be used
in midspan systems.
The MAX5945 provides input undervoltage lockout,
input undervoltage detection, input overvoltage lockout,
overtemperature protection, output-voltage slew-rate
limit during startup, power-good status, and fault
status. The MAX5945’s programmability includes
gate-charging current, current-limit threshold, startup
timeout, overcurrent timeout, autorestart duty cycle, PD
disconnect AC detection threshold and PD disconnect
detection timeout.
The MAX5945 communicates with the system
microcontroller through an I2C-compatible interface.
The MAX5945 features separate input and output data
lines (SDAIN and SDAOUT) for use with optocoupler
isolation. The MAX5945 is a slave device. Its four
address inputs allow 16 unique MAX5945 addresses. A
separate INT output and four independent shutdown
inputs (SHD_) allow fast interrupt signals between the
MAX5945 and the microcontroller. A RESET input
allows hardware reset of the device.
Reset
Reset is a condition the MAX5945 enters after any of
the following conditions:
After power-up (VEE and VDD rise above their UVLO
thresholds).
Hardware reset. The RESET input is driven low and
up high again any time after power-up.
Software reset. Writing a 1 into R1Ah[4] any time
after power-up.
Thermal shutdown.
During a reset, the MAX5945 resets its register map to
the reset state as shown in Table 30 and latches in the
state of AUTO (pin 35) and MIDSPAN (pin 2). During
normal operation, changes at the AUTO and MIDSPAN
inputs are ignored. While the condition that caused the
reset persists (i.e., high temperature, RESET input low,
or UVLO conditions) the MAX5945 will not acknowl-
edge any addressing from the serial interface.
Port Reset (R1Ah[3:0])
Set high anytime during normal operation to turn off
power and clear the events and status registers of the
corresponding port. Port reset only resets the events
and status registers.
Operation Modes
The MAX5945 contains four independent but identical
state machines to provide reliable and real-time control
of the four network ports. Each state machine has four
different operating modes: auto, semi-auto, manual,
and shutdown. Auto mode allows the device to operate
automatically without any software supervision. Semi-
auto mode, upon request, continuously detects and
classifies a device connected to a port but does not
power up that port until instructed by software. Manual
mode allows total software control of the device and is
useful in system diagnostic. Shutdown mode terminates
all activities and securely turns off power to the ports.
Switching between AUTO, SEMI, or MANUAL mode
does not take effect until the part finishes its current
task. When the port is set into SHUTDOWN mode, all
the port operations are immediately stopped and the
port remains idle until SHUTDOWN is exited.
Automatic (AUTO) Mode
Enter automatic (AUTO) mode by forcing the
AUTO input high prior to a reset, or by setting
R12h[P_ M1,P_M0] to [1,1] during normal operation
(see Tables 15 and 15a). In AUTO mode, the MAX5945
performs detection, classification, and powers up the
port automatically once a valid PD is detected at the
port. If a valid PD is not detected at the port, the
MAX5945 repeats the detection routine continuously
until a valid PD is detected.
Going into AUTO mode, the DET_EN and CLASS_EN
bits are set to high and stay high unless changed by
software. Using software to set DET_EN and/or
CLASS_EN low causes the MAX5945 to skip detection
and/or classification. As a protection, disabling the
detection routine in AUTO mode will not allow the corre-
sponding port to power up, unless the DET_BYP
(R23H[4]) is set to 1.
The AUTO status is latched into the register only during
a reset. Any changes to the AUTO input after reset is
ignored.
Semi-Automatic (SEMI) Mode
Enter semi-automatic (SEMI) mode by setting
R12h[P_M1,P_M0] to [1,0] during normal operation
(see Tables 15 and 15a). In SEMI mode, the MAX5945,
upon request, performs detection and/or classification
repeatedly but does not power up the port(s), regard-
less of the status of the port connection.
MAX5945
Quad Network Power Controller
for Power-Over-LAN
______________________________________________________________________________________
13
相關PDF資料 |
PDF描述 |
|---|---|
| ENC28J60T/ML | IC ETHERNET CTRLR W/SPI 28QFN |
| ENC28J60/SP | IC ETHERNET CTRLR W/SPI 28DIP |
| 413760-5 | CONN JACK BNC AT&T 728 HEX CRIMP |
| ENC28J60/SO | IC ETHERNET CTRLR W/SPI 28SOIC |
| ENC28J60/ML | IC ETHERNET CTRLR W/SPI 28QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX5945EVKIT | 功能描述:電源管理IC開發工具 Evaluation Kit/Evaluation System for the MAX5945 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX5945EVSYS | 功能描述:電源管理IC開發工具 Evaluation Kit/Evaluation System for the MAX5945 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX5946AETJ | 制造商:Maxim Integrated Products 功能描述:DUAL PCI-EXPRESS HOT-PLUG CONTROLLER - Rail/Tube |
| MAX5946AETX | 功能描述:熱插拔功率分布 RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| MAX5946AETX+ | 功能描述:熱插拔功率分布 Dual PCIe Hot-Plug Controller RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。