參數資料
型號: MAX7456EVKIT+
廠商: Maxim Integrated Products
文件頁數: 37/44頁
文件大?。?/td> 0K
描述: KIT EVAL FOR MAX7456
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 1
主要目的: 視頻,屏幕顯示器(OSD)
嵌入式: 是,MCU,16 位
已用 IC / 零件: MAX7456
主要屬性: NTSC/PAL 單通道單色屏幕顯示器(OSD),帶集成視頻驅動器
次要屬性: GUI,SPI 接口
已供物品:
產品目錄頁面: 1424 (CN2011-ZH PDF)
Single-Channel Monochrome On-Screen
Display with Integrated EEPROM
Multiple OSDs with
Common Clock Application
The MAX7456 provides a TTL clock output (CLKOUT)
capable of driving one CLKIN pin of another MAX7456.
Two or more MAX7456 parts can be driven using an
external clock driver. This arrangement reduces the
system cost by having only one crystal on one
MAX7456 that supplies the clock signal to multiple
MAX7456 parts (Figure 25).
Selecting a Clock Crystal
Choose a 27MHz parallel resonant, fundamental mode
crystal. No external load capacitors are needed. All
capacitors required for the Pierce oscillator are includ-
ed on-chip.
Power Supply and Bypassing
The MAX7456 operates from three independent supply
lines. Each supply must be within a +4.75V to +5.25V
voltage range. Separate the digital power supply from
the analog and video-driver supply lines to prevent
high-frequency digital noise that may couple onto the
video output. All three supplies should be at the same
DC voltage. Bypass each supply with a 0.1F capacitor
to ground very close to the IC pins. There are no
power-supply sequencing requirements for the device.
Layout Concerns
For best performance, make the VIN and VOUT traces
as short as possible. Place all AC-coupling capacitors
and 75
Ω termination resistors close to the device with
the resistors terminated to the solid analog ground
plane. Since the MAX7456 TSSOP package has an
exposed pad (EP) underneath, do not run traces under
the package to avoid possible short circuits. Refer to
the MAX7456 EV kit for an example of PCB layout.
To aid heat dissipation, the EP should be connected to
a similarly sized pad on the component side of the
PCB. This pad should be connected through to the sol-
der-side copper by several plated holes to conduct
heat away from the device. The solder-side copper pad
area should be larger than the EP area. It is recom-
mended that the EP be connected to ground, but it is
not required. Do not use EP as the only ground connec-
tion for the device.
28
27
26
25
24
23
22
21
20
19
18
17
16
15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
N.C.
VOUT
SAG
PVDD
PGND
N.C.
VIN
AVDD
AGND
RESET
HSYNC
VSYNC
N.C.
LOS
SDOUT
SCLK
SDIN
CS
CLKOUT
XFB
CLKIN
DGND
DVDD
N.C.
TSSOP
TOP VIEW
MAX7456
+
Pin Configuration
Chip Information
PROCESS: BiCMOS
MAX7456
42
Maxim Integrated
相關PDF資料
PDF描述
EMM10DSEP-S243 CONN EDGECARD 20POS .156 EYELET
H3AAH-4036G IDC CABLE - HSC40H/AE40G/HSC40H
1025R-42K COIL 8.2UH MOLDED UNSHIELDED
V375C24E150BL3 CONVERTER MOD DC/DC 24V 150W
GEM28DTMS-S189 CONN EDGECARD 56POS R/A .156 SLD
相關代理商/技術參數
參數描述
MAX7456EVKIT+ 功能描述:顯示開發工具 MAX7456 Eval Kit RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V
MAX7457ETE 功能描述:視頻開關 IC RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻(最大值):12 Ohms 傳播延遲時間: 開啟時間(最大值): 關閉時間(最大值): 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel
MAX7457ETE+ 功能描述:視頻開關 IC Video Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻(最大值):12 Ohms 傳播延遲時間: 開啟時間(最大值): 關閉時間(最大值): 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel
MAX7457ETE+T 功能描述:視頻開關 IC Video Switch for Dual SCART Connector RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻(最大值):12 Ohms 傳播延遲時間: 開啟時間(最大值): 關閉時間(最大值): 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel
MAX7457ETE-T 功能描述:視頻開關 IC RoHS:否 制造商:Texas Instruments 開關數量:4 開啟電阻(最大值):12 Ohms 傳播延遲時間: 開啟時間(最大值): 關閉時間(最大值): 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:WQFN-42 封裝:Reel