- 您現在的位置：買賣IC網 > PDF目錄11700 > MAX9258GCM/V+ (Maxim Integrated Products)IC SER/DESER PROG 48-LQFP PDF資料下載
參數資料
| 型號： | MAX9258GCM/V+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 25/52頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SER/DESER PROG 48-LQFP |
| 其它有關文件： | Automotive Product Guide |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 250 |
| 功能： | 串行器/解串器 |
| 數據速率： | 840Mbps |
| 輸入類型： | 串行 |
| 輸出類型： | LVDS |
| 輸入數： | 1 |
| 輸出數： | 16 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 105°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
Assuming a UART bit rate of 2Mbps, REG2[7:4],
REG3[7:4] = 100 (Table 26), CTO = 64, CTO timeout
calculated as:
tCTO = (0.5s)
× 64 = 32s
Link Power-Up
The MAX9258 powers up when the power-down input
PD goes high. After approximately 130s, CCEN goes
high, indicating the control channel is available. This
delay is required because the analog circuitry has to
fully wake up. There are two ways to power up the
MAX9257. The MAX9257 powers up according to the
state of REM. ECU powers up MAX9257 remotely (ECU
sends command to power up) when REM is pulled to
VCC. The MAX9257 powers up according to the supply
voltage when REM is grounded.
Powering the MAX9257 with Serialization Enabled
(REM = Ground at Power-Up)
When REM is grounded, the MAX9257 fully powers up
when power is applied. The power-down bit PD
(REG4[4]) is disabled and serialization bit SEREN
(REG4[3]) is enabled. If PCLK_IN is not running, the
MAX9257 stays in the control channel. After PCLK_IN is
applied, the control channel times out due to STO, ETO,
or EF. The MAX9257 starts the handshaking after the
MAX9257 locks to PCLK after 32,768 clock cycles. If
PCLK_IN is running, serialization starts automatically
after PLL of the MAX9257 locks to PCLK_IN with default
values in the registers.
Remote Power-Up of the MAX9257
(REM = Pulled Up to VCC)
When REM is pulled up to VCC, the MAX9257 wakes up
in a low power state, drawing less than 100A supply
current. To wake-up the MAX9257, the ECU first trans-
mits a dummy frame 0xDB and then waits at least
100s to allow the MAX9257’s internal analog circuitry
to fully power up. Then the ECU configures the
MAX9257 registers, including a write to disable the PD
bit (REG4[4]) so that the MAX9257 does not return
back to the low power state. Every packet needs to
start with a synchronization frame (see the
UART sec-
tion). If the PD bit is not disabled within 70ms after
transmitting the dummy frame, the MAX9257 returns to
the low power state and the whole power-up sequence
needs to be repeated. After configuration is complete,
the ECU also needs to enable the SEREN bit to start the
video phase.
At initial power-up with REM pulled to VCC, default value
of SEREN bit is 0, so STO and ETO timers are not active.
Control channel is enabled as long as SEREN is 0.
This allows the control channel to be used for extensive
programming at initial power-up without the channel
timing out. UART, parity, framing and packet errors in
the control channel communications are reported if end
frame is used to close control channel (see the
MAX9258 Error Checking and Reporting section). For
faster identification of errors, verify every write com-
mand by reading back the registers before enabling
serialization.
Link Power-Down
When the control channel is open, the ECU writes to the
PD bit to power down the MAX9257. In this case, to
power up the MAX9257 again, the power-up sequence
explained in the
Remote Power-Up of the MAX9257 (REM
= Pulled Up to VCC) section needs to be repeated. The
MAX9258 has a
PD input that powers down the device.
MAX9258 Error Checking and Reporting
The MAX9258 has an open-drain
ERROR output. This
output indicates various error conditions encountered
during the operation of the system. When an error con-
dition is detected and needs to be reported,
ERROR
asserts low.
ERROR indicates three error conditions:
UART, video parity, and PRBS errors.
UART Errors
During control channel communication in base mode,
the MAX9257/MAX9258 record UART frame, parity, and
packet errors. I2C errors are also recorded by
MAX9257 when I2C interface is enabled. If ECU closes
the control channel by using end frame (EF), the
MAX9257 sends a special internal UART frame back to
the MAX9258 called error frame. The MAX9257 UART
and I2C errors are reset at the next control channel. The
MAX9258 receives the error frame and records the
error status in its UART error register (REG13). ECU
must use end frame to the close control channel for the
MAX9257 to report back UART and I2C errors to the
MAX9258. Whenever one of the bits in the UART error
register is 1,
ERROR asserts low. The UART error regis-
ter is reset when ECU reads it, and
ERROR deasserts
high immediately if UART errors were the only reason
that
ERROR was asserted low. If the MAX9258 is not
locked (LOCK = low), UART error is not reported.
Video Parity Errors
When video parity check is enabled (REG0[3] in both
devices), the MAX9258 counts the number of video pari-
ty errors by checking recovered video words. Value of
this counter is reflected in PAERRHI (8 MSB bits,
REG11) and PAERRLO (8 LSB bits, REG10). If the num-
ber of detected parity errors is greater than or equal to
the parity error threshold PATHRHI (REG9) and
PATHRLO (REG8), then
ERROR asserts low. In this
MAX9257/MAX9258
______________________________________________________________________________________
31
Fully Programmable Serializer/Deserializer
with UART/I2C Control Channel
相關PDF資料 |
PDF描述 |
|---|---|
| C8051F541-IM | IC 8051 MCU 16K FLASH 32-QFN |
| MS27484E18F35S | CONN PLUG 66POS STRAIGHT W/SCKT |
| D38999/24JA98PN | CONN RCPT 3POS JAM NUT W/PINS |
| R5F1008AALA#U0 | MCU 16BIT 16KB FLASH 25FLGA |
| MS-162A | CONN RECEPT COAX SWITCHING SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9259 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Gigabit Multimedia Serial Link with Spread Spectrum and Full-Duplex Control Channel |
| MAX9259EVKIT+ | 功能描述:界面開發工具 MAX9259 Eval Kit RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| MAX9259GCB/V+ | 功能描述:串行器/解串器 - Serdes Multimedia Serial Link RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9259GCB/V+T | 功能描述:串行器/解串器 - Serdes Multimedia Serial Link RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64 |
| MAX9259GCB/V+TGG4 | 功能描述:串行器/解串器 - Serdes Mltimedia Ser Link w/ Spread Spectrum RoHS:否 制造商:Maxim Integrated 類型: 數據速率: 輸入類型: 輸出類型: 輸入端數量: 輸出端數量: 工作電源電壓: 工作溫度范圍: 封裝 / 箱體: |
發布緊急采購，3分鐘左右您將得到回復。