- 您現在的位置：買賣IC網 > PDF目錄1946 > MAX9671CTH+T (Maxim Integrated Products)IC AUDIO/VIDEO SWIT DUAL 44TQFN PDF資料下載
參數資料
| 型號： | MAX9671CTH+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AUDIO/VIDEO SWIT DUAL 44TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 功能： | 音頻/視頻切換 |
| 電路： | 2 x SCART |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3.3 V ~ 12 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 44-TQFN-EP（7x7） |
| 包裝： | 帶卷 (TR) |
| 配用： | MAX9671EVKIT+-ND - EVALUATION KIT FOR MAX9671 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
18
______________________________________________________________________________________
video sources that are sent to the VCR SCART connec-
tor are controlled by bits 0 to 2 of the VCR Video Input
Control register (08h). See Tables 10, 14, and 16. The
video outputs can be enabled or disabled by bits 2
through 7 of the Output Enable register (0Dh). See
Table 18.
Slow Switching
The MAX9670/MAX9671 support the IEC 933-1,
Amendment 1, three-level slow switching that selects
the aspect ratio for the display (TV). Under I2C control,
the MAX9670/MAX9671 set the slow-switching output
voltage level. Table 2 shows the valid input levels of the
slow-switching signal and the corresponding operating
modes of the display device.
Two bidirectional ports are available for slow-switching
signals for the TV and VCR. The slow-switching input
status is continuously read and stored in the Status reg-
ister (0Eh). The slow-switching outputs can be set to a
logic level or high impedance by writing to the TV Video
Output Control register (07h) and the VCR Video Output
Control register (09h). When enabled, INT becomes
active low if the voltage level changes on TV_SS or
VCR_SS. See Tables 10, 15, 17, and 20.
Fast Switching
The fast-switching signal was originally used to switch
between CVBS and RGB signals on a pixel-by-pixel
basis so that on-screen display (OSD) information
could be inserted. Since modern set-top box decoder
chips have integrated OSD circuitry, there is no need to
create OSD information using the older technique. Now,
the fast-switching signal is just used to switch between
CVBS and RGB signal sources.
Set the source of the fast-switching signal by writing to
bits 4 and 3 of the TV Video Output Control register
(07h). The fast-switching signal to the TV SCART con-
nector can be enabled or disabled by bit 1 of the Output
Enable register (0Dh). See Tables 10, 15, and 18.
I2C Serial Interface
The MAX9670/MAX9671 feature an I2C/SMBus-com-
patible, 2-wire serial interface consisting of a serial-data
line (SDA) and a serial-clock line (SCL). SDA and SCL
facilitate communication between the MAX9670/
MAX9671 and the master at clock rates up to 400kHz.
Figure 6 shows the 2-wire interface timing diagram. The
master generates SCL and initiates data transfer on the
bus. A master device writes data to the MAX9670/
MAX9671 by transmitting a START (S) condition, the
proper slave address with the R/W bit set to 0, followed
by the register address and then the data word. Each
transmit sequence is framed by a START and a STOP
(P) condition. Each word transmitted to the
MAX9670/MAX9671 is 8 bits long and is followed by an
acknowledge clock pulse. A master reads from the
MAX9670/MAX9671 by transmitting the slave address
with the R/W bit set to 0, the register address of the reg-
ister to be read, a REPEATED START (Sr) condition, the
slave address with the R/W bit set to 1, followed by a
series of SCL pulses. The MAX9670/MAX9671 transmit
data on SDA in sync with the master-generated SCL
pulses. The master acknowledges receipt of each byte
of data. Each read sequence is framed by a START or
MAX9670 fig04
20
s/div
INPUT
500mV/div
OUTPUT
500mV/div
Figure 4. MAX9670/MAX9671 Video Output with CVBS Signal,
Multiburst Video Test Signal Shown
MAX9670 fig05
10
s/div
INPUT
200mV/div
OUTPUT
200mV/div
Figure 5. MAX9670/MAX9671 Video Output with Chroma (C)
Signal, Multiburst Video Test Signal Shown
相關PDF資料 |
PDF描述 |
|---|---|
| MAX9675ECQ+ | IC CROSSPOINT SWIT 16X16 100TQFP |
| MAX9921AUB/V+T | IC HALL EFFECT SENSOR DL 10UMAX |
| MAX9925AUB+ | IC SENSOR INTERFACE VARI 10MSOP |
| MAX9950DCCB+TD | IC PMU DUAL 64TQFP |
| MAX9952FCCB+T | IC PMU DUAL 64TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9671EVKIT+ | 功能描述:交換機 IC 開發工具 Low-Power A/V Switch w/Audio Volume Cntrl RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| MAX9672ETI+ | 功能描述:LCD Gamma緩沖器 10-Bit Prog Gamma Reference System RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| MAX9672ETI+T | 功能描述:LCD Gamma緩沖器 10-Bit Prog Gamma Reference System RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| MAX9672EVKIT+ | 功能描述:LCD Gamma緩沖器 Integrated Circuits (ICs) Video Processing - KIT EVALUATION FOR MAX9672 RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| MAX9673ETI+ | 功能描述:LCD Gamma緩沖器 10-Bit Prog Gamma Reference System RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。