參數資料
型號: MAX9671CTH+T
廠商: Maxim Integrated Products
文件頁數: 7/44頁
文件大?。?/td> 0K
描述: IC AUDIO/VIDEO SWIT DUAL 44TQFN
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
功能: 音頻/視頻切換
電路: 2 x SCART
電壓電源: 單電源
電壓 - 電源,單路/雙路(±): 3.3 V ~ 12 V
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 44-WFQFN 裸露焊盤
供應商設備封裝: 44-TQFN-EP(7x7)
包裝: 帶卷 (TR)
配用: MAX9671EVKIT+-ND - EVALUATION KIT FOR MAX9671
MAX9670/MAX9671
Low-Power Audio/Video Switch with Audio
Volume Control for Dual SCART Connectors
______________________________________________________________________________________
15
Clickless Switching
The TV audio channel incorporates a zero-crossing
detect (ZCD) circuit that minimizes click noise due to
abrupt signal level changes that occur when switching
between audio signals at an arbitrary moment.
To implement the zero-crossing function when switch-
ing audio signals, set the ZCD bit high (Audio Control
register 00h, bit 6). Then set the mute bit high (Audio
Control register 00h, bit 0). Next, wait for a sufficient
period of time for the audio signal to cross zero. This
period is a function of the audio signal path’s low-fre-
quency 3dB corner (fL3dB). Thus, if fL3dB = 20Hz, the
time period to wait for a zero-crossing detect is 1/20Hz
or 50ms.
After the wait period, select a new audio source for the
TV audio channel by writing to bits 1 and 0 of TV Audio
Control register (01h). Finally, clear mute (Audio Control
register, 00h, bit 0), but leave ZCD (Audio Control reg-
ister 00h, bit 6) high. The MAX9670/MAX9671 switches
the signal out of mute at the next zero crossing. See
Tables 12 and 13.
Audio Outputs
The MAX9670/MAX9671 audio output amplifiers feature
Maxim’s DirectDrive architecture, thereby eliminating
the need for output-coupling capacitors required by
conventional single-supply audio line drivers. An inter-
nal charge pump inverts the positive supply (VAUD),
creating a negative supply (CPVSS). The audio output
amplifiers operate from these bipolar supplies with their
outputs biased about audio ground (Figure 2). The ben-
efit of this audio ground bias is that the amplifier out-
puts do not have a DC component. The DC-blocking
capacitors required with conventional audio line drivers
are unnecessary, conserving board space, reducing
system cost, and improving frequency response.
Conventional single-supply audio line drivers have their
outputs biased about a nominal DC voltage (typically
half the supply) for maximum dynamic range. Large
coupling capacitors are needed to block this DC bias.
Clicks and pops are created when the coupling capaci-
tors are charged during power-up and discharged dur-
ing power-down.
The MAX9670/MAX9671 features a low-noise charge
pump that requires only two small ceramic capacitors.
The 580kHz switching frequency is well beyond the
audio range and does not interfere with audio signals.
The switch drivers feature a controlled switching speed
that minimizes noise generated by turn-on and turn-off
transients.
The SCART standard specifies 2VRMS as the full-scale
for audio signals. As the audio circuits process
0.5VRMS full-scale audio signals internal to the
MAX9670/MAX9671, the gain-of-4 output amplifiers
restore the audio signals to a full-scale of 2VRMS.
To select which audio input source is routed to the TV
SCART connector, write to bits 1 and 0 of the TV Audio
Control register (01h). To select which audio input
source is routed to the VCR SCART connector, write to
bits 3 and 2 of the TV Audio Control register (01h). The
power-on default is for the TV and VCR audio outputs to
be muted (the inputs of the output amplifiers are con-
nected to audio ground). See Tables 10 and 13.
Volume Control
Volume control is programmable from -62dB to 0dB in
2dB steps through I2C interface. The block consists of
a resistive ladder network to generate 31 2dB volume
control steps, a unity gain buffer to isolate the input
from the resistive ladder, switches (MPLx and MNLx)
that select 1 of 32 nodes on the resistive ladder, and
logic to decode the the I2C volume control value. See
Table 12.
+VDD
-VDD
GND
VOUT
CONVENTIONAL DRIVER-BIASING SCHEME
DirectDrive BIASING SCHEME
VDD/2
VDD
GND
2VDD
Figure 2. Conventional Driver Output Waveform vs. MAX9670/
MAX9671 Output Waveform.
相關PDF資料
PDF描述
MAX9675ECQ+ IC CROSSPOINT SWIT 16X16 100TQFP
MAX9921AUB/V+T IC HALL EFFECT SENSOR DL 10UMAX
MAX9925AUB+ IC SENSOR INTERFACE VARI 10MSOP
MAX9950DCCB+TD IC PMU DUAL 64TQFP
MAX9952FCCB+T IC PMU DUAL 64TQFP
相關代理商/技術參數
參數描述
MAX9671EVKIT+ 功能描述:交換機 IC 開發工具 Low-Power A/V Switch w/Audio Volume Cntrl RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V
MAX9672ETI+ 功能描述:LCD Gamma緩沖器 10-Bit Prog Gamma Reference System RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
MAX9672ETI+T 功能描述:LCD Gamma緩沖器 10-Bit Prog Gamma Reference System RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
MAX9672EVKIT+ 功能描述:LCD Gamma緩沖器 Integrated Circuits (ICs) Video Processing - KIT EVALUATION FOR MAX9672 RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube
MAX9673ETI+ 功能描述:LCD Gamma緩沖器 10-Bit Prog Gamma Reference System RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube