- 您現在的位置：買賣IC網 > PDF目錄1946 > MAX9952FCCB+T (Maxim Integrated Products)IC PMU DUAL 64TQFP PDF資料下載
參數資料
| 型號： | MAX9952FCCB+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PMU DUAL 64TQFP |
| 標準包裝： | 750 |
| 系列： | * |
MAX9951/MAX9952
Dual Per-Pin Parametric
Measurement Units
15
Maxim Integrated
Use
LOAD to asynchronously load all input registers
into the PMU registers. If
LOAD remains low when data
latches into an input register, the data also transfers to
the PMU register.
PMU Control
Programming both PMUs with the same data requires a
16-bit word. Programming each PMU with separate
data requires two 16-bit words.
The address bits specify which input registers the shift-
register loads. Table 2 describes the function of the
address bits.
Bits C1 and C2 specify how the data loads into the sec-
ond rank PMU registers. These 2 control bits serve a
similar function as the
LOAD input. The specified
actions occur when
CS goes high, whereas the LOAD
input loads the PMU register at anytime. When either
C1 or C2 is low, the corresponding PMU register is
transparent. Table 3 describes the function of the 2
control bits.
The NOP operation requires A1 = A2 = C1 = C2 = 0. In
this case, the data transfers through the shift register
without changing the state of the device.
D0
D1
D15
CONTROL
DECODE
INPUT REGISTER A
INPUT REGISTER B
PMU REGISTER A
SCLK
DIN
PMU REGISTER B
DOUT
LOAD
12
TO PMUA
12
TO PMUB
12
4
CS
Figure 4. Dual PMU Serial Port Block Diagram
Table 1. Bit Assignments
BIT
BIT NAME
15
INMODE
14
FMODE
13
MMODE
12
RS2
11
RS1
10
RS0
9
CLENABLE
8
HI-ZFORCE
7
HI-ZMSR
6
DISABLE
5B2
4B1
3A2
2A1
1C2
0C1
Table 2. Address Bit
A2
A1
OPERATION
0
Do not update any input register (NOP).
0
1
Only update input register A.
1
0
Only update input register B.
11
Update both input registers with the same
data.
Table 3. Control Bit
C2
C1
OPERATION
0
Data stays in input register.
01
Transfer PMU-A input register to PMU
register.
10
Transfer PMU-B input register to PMU
register.
11
Transfer both input registers to the PMU
registers.
相關PDF資料 |
PDF描述 |
|---|---|
| MAXQ2000-RAX+ | IC MCU 32K FLASH 68-QFN |
| MAXQ2010-RFX+ | IC MCU 16BIT 64KB FLASH 100-LQFP |
| MAXQ3120-FFN+ | IC MCU 32KB FLASH 80-MQFP |
| MAXQ3210-EMX+ | IC MCU 16BIT LP 24-DIP |
| MAXQ3212-EJX+ | IC MCU 16BIT LP 24-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX9952FCCB-TD | 功能描述:接口 - 專用 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX9955BDCCB+D | 制造商:Maxim Integrated Products 功能描述:DUAL DRIVER/TERMINATOR WITH CABLE-D - Rail/Tube |
| MAX9955BDCCB-D | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9955BDCCB-TD | 功能描述:校驗器 IC RoHS:否 制造商:STMicroelectronics 產品: 比較器類型: 通道數量: 輸出類型:Push-Pull 電源電壓-最大:5.5 V 電源電壓-最小:1.1 V 補償電壓（最大值）:6 mV 電源電流（最大值）:1350 nA 響應時間: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SC-70-5 封裝:Reel |
| MAX9957CCB+D | 制造商:Maxim Integrated Products 功能描述:FAST DUAL DRIVER FOR ATE WITH WAVEF - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。