- 您現在的位置：買賣IC網 > PDF目錄377932 > MB91307RPFV (FUJITSU LTD) 32-Bit Microcontroller PDF資料下載
參數資料
| 型號： | MB91307RPFV |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 32-Bit Microcontroller |
| 中文描述： | 32-BIT, 66 MHz, RISC MICROCONTROLLER, PQFP120 |
| 封裝： | LEAD FREE, PLASTIC, LQFP-120 |
| 文件頁數： | 15/96頁 |
| 文件大?。?/td> | 963K |
| 代理商： | MB91307RPFV |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁
MB91307 Series
15
Sample use of Stop Mode with 3.3 V power supply
About crystal oscillator circuit
Noise near the X0 and X1 pins may cause the device to malfunction. Design the printed circuit board so that
X0, X1, the crystal oscillator (or ceramic oscillator) , and the bypass capacitor to ground are located as close to
the device as possible.
It is strongly recommended to design the PC board artwork with the X0 and X1 pins surrounded by ground plane
because stable operation can be expected with such a layout.
Treatment of NC pins
Any pins marked “NC” (not connected) must be left open.
About mode pins (MD0 to MD2)
Mode pins (MD0 to MD2) should be connected directly to V
CC
or V
SS
.
To prevent the device erroneously switching to test mode due to noise, design the printed circuit board such that
the distance between the mode pins and V
CC
or V
SS
is as short as possible and the connection impedance is low.
Operation at startup
Immediately after a power-on startup, always apply a reset initialization (INIT) at the INIT pin. Also, in order to
assure a wait period for the oscillator circuits to stabilize immediately after startup, be sure that the “L” level input
to the INIT pin continues for the required stabilization wait interval. (The INIT cycle for the INIT pin includes only
the minimum setting for the stabilization wait period.)
Base oscillator input at startup
At power-on startup, always input a clock signal until the oscillator stabilization wait period is ended.
Caution on Operations during PLL Clock Mode
If the PLL clock mode is selected, the microcontroller attempt to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
Precaution on using ports 6 and 7
If one of P60/A15 to P70/A24, which are shared for output of external bus interface addresses, is used as a port,
a grid voltage is applied to the port instantaneously when the status of another address output pin is changed.
Therefore, add resistors or capacitors to those ports to prevent application of the grid voltage.
V
CC
C
V
SS
0.1 F
3.3 V
2.4 k
7.6 k
GND
相關PDF資料 |
PDF描述 |
|---|---|
| MB91307 | 32-Bit Microcontroller |
| MB91354APMT | 32-Bit Proprietary Microcontroller |
| MB91V350A | 32-Bit Proprietary Microcontroller |
| MB91F355APMT-002 | 32-Bit Proprietary Microcontroller |
| MB91F356BPMT | 32-Bit Proprietary Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB91310 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Proprietary 32-bit Microcontroller |
| MB91314A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91314APMC-GE1 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller |
| MB91316 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
| MB91316A | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。